k608i HELP -tried to unlock now only red light flashing

[atmot]

Used setool2, k608i, presssed unlock/repair says that its unlocked but now only red light flashing when i press power... what do i do????

GUI v0.91373/UNI
standalone version engaged.
Card serial:00001283
Loaded 49 flash descriptors
Open COM port OK
Elapsed:12 secs.
Open COM port OK
Elapsed:7 secs.
RECOVERY MODE STARTED
Open COM port OK
Elapsed:83 secs.
Open COM port OK
Elapsed:9 secs.
Open COM port OK
ChipID:7100,EMP protocol:0301
PHONE IS BROWN
FLASH CID detected:37
Speed:115200
OTP status:0 locked:1 CID:37 PAF:1 IMEI:35684100002695 CERT:BROWN
Loader:041214 0759 MATCXC1325712_PRODUCTION R2Z
Flash ID check:890D
Flash props sent ok
Setting up gdfs...
Clearing total time...
Writing simlocks...
Signing...
control keys complete.
full sig complete.
Unlock Done
Elapsed:15 secs.


this is my first time - so anyone that can help me step by step would be greatly appreciated ..
thanks in advance for anyone willing to share their knowledge..

[fonecellar]

Used setool2, k608i, presssed unlock/repair says that its unlocked but now only red light flashing when i press power... what do i do????



this is my first time - so anyone that can help me step by step would be greatly appreciated ..
thanks in advance for anyone willing to share their knowledge..

reattach and change fone colour back to red ;)

[atmot]

you mean "CID change" to red37?
then press unlock again?
excuse my ignorance,, 1st timer

[GOLAM]

if you have a usb-smart just do the unlock process again. it will be ok.
priviously i faced the same problem with setools and fixed with usb-smart. you do not need to flash. just unlock process with another tools.

[leroi]

hello man
u have the best tool to resolve your problem
fist select in cid tab select brown 37
and press flash flash , please in seting tab do not select complete phone
if no work select red 37 and press flash .

try and reply there

[GOLAM]

check here u can find semc tools
http://www.unlockeasy.com/modules.php?name=Downloads&d_op=viewdownloaddetails&lid=697&title=USB-Smart%20SEMC%20Tool%203.3

[atmot]

GUI v0.91373/UNI
standalone version engaged.
Card serial:00001283
Loaded 49 flash descriptors
Open COM port OK
Elapsed:12 secs.
Open COM port OK
Elapsed:7 secs.
RECOVERY MODE STARTED
Open COM port OK
Elapsed:83 secs.
Open COM port OK
Elapsed:9 secs.
Open COM port OK
ChipID:7100,EMP protocol:0301
PHONE IS BROWN
FLASH CID detected:37
Speed:115200
OTP status:0 locked:1 CID:37 PAF:1 IMEI:35684100002695 CERT:BROWN
Loader:041214 0759 MATCXC1325712_PRODUCTION R2Z
Flash ID check:890D
Flash props sent ok
Setting up gdfs...
Clearing total time...
Writing simlocks...
Signing...
control keys complete.
full sig complete.
Unlock Done
Elapsed:15 secs.
Open COM port OK
ChipID:7100,EMP protocol:0301
PHONE IS BROWN
FLASH CID detected:37
Speed:115200
OTP status:0 locked:1 CID:37 PAF:1 IMEI:35684100002695 CERT:BROWN
Loader:041214 0759 MATCXC1325712_PRODUCTION R2Z
Flash ID check:890D
Flash props sent ok
Switching to USB...
Phone stays at current interface.
Flashing MAIN firmware:C:\2\z1010\DEL_125432_041108_1443_R1K010{ 0102020101}.out
can't open file "C:\2\z1010\DEL_125432_041108_1443_R1K010{010202010 1}.out"
Elapsed:17 secs.

[leroi]

if this is no work go there please



http://www.************.com/forum/showthread.php?t=24977

do this first please before what i post before
best wishes
leroi

[fonecellar]

you mean "CID change" to red37?
then press unlock again?
excuse my ignorance,, 1st timer

yes @atmot all you have to do is cid change to red . should be simpl as that if you show red light, all k 608i MUST be return to red

[leroi]

please this mean that you want to write z1010 flash file on your phone man

there must not be flash file on main et fs tab man

this is why you must
press first

"clean file in main tab


************************************************** *******

now restart soft
go in setting tab

1- select in setting check "convert to red"
then unlock
and your problem will be resolve

do this please an post here
leroi
and you can contact me in my yahoo messenger
my iden is
tnguila@yahoo.fr
leroi
best wishes

[leroi]

@atmot

i'm waitting for u man
leroi

[atmot]

thank you heaps guys... problem fixed.... really appreciate you time and help......
:) :) :)

[leroi]

i'm very happy to see that your problem is resolved

if you want to debrand your phone you must
go in support of your dongle page i mean www.s.....org
and dowload k600 flash files same as K608, but the problem is there are not flash file with cid 37
u must first change cid and flash
1- main + fs
2- complete checking of setting tab
3- press flash

but i thing u have not more experience for doing this kind of operation perhaps if you take time to read and understand faq on support forum

best regard
leroi


1-

[fonecellar]

its ok i have PM with @atmot and explained it will be a problem for him as a newbie to debrand and his fone now all 100% ;)