3310 M-bus error, please help!!

[hskc2005]

please anyone got solution for nokia 3310 flashes but when concluding gives this error: "M-bus error 1F 00 10 40 00 04 00 01 64 03 01 2C bad mob" ACK


how to get solve this problems?

[yummy]

yeah i too have same problem i think that is the problem of flash.......or any body can help

[enson uk]

pls i have 3310/1100 flash id fail or power up fail any solution

[enson uk]

2100 power on in system but not with pls help

[gokul2005]

3310 M-bus error, please help!!

--------------------------------------------------------------------------------

please anyone got solution for nokia 3310 flashes but when concluding gives this error: "M-bus error 1F 00 10 40 00 04 00 01 64 03 01 2C bad mob" ACK



1)flash mcu,ppm,pmm

2)then flash mcu ppm,+rebuild imei+ui settings
3)set will be ok

[Lanz]

pls i have 3310/1100 flash id fail or power up fail any solution


Bro Just try to change flah IC :D

[.:VodaFone:.]

please anyone got solution for nokia 3310 flashes but when concluding gives this error: "M-bus error 1F 00 10 40 00 04 00 01 64 03 01 2C bad mob" ACK


how to get solve this problems?

Check your connector, if not ok rehot some capacitors near connector.

[zeeqsystems]

[QUOTE=hskc2005;1993222]please anyone got solution for nokia 3310 flashes but when concluding gives this error: "M-bus error 1F 00 10 40 00 04 00 01 64 03 01 2C bad mob" ACK


1Clean the pcb's connector area,
2.Change your cable

[Lanz]

Bro, try to flash by using dejan or Banana flasher. ufter flash carculate using by Noktool. Pls elaborate if what fhasher you use?

[slowik]

Make sure you have lastest suite version

[elvislano]

sir try another flasher like babana software.. it will be okey

[elvislano]

pls i have 3310/1100 flash id fail or power up fail any solution

sir try to reheat flash ic and flash it again with high version

[jcomputers@redi]

nothing helped me!!!!!!!!!!!!!!! give some perfect sol. or stop joking

[elvislano]

2100 power on in system but not with pls help

what the history of your phone... but you can try another flasher like jaf...

[cell2cell]

l have the same problem the phone came in for simply unlock when l connected it to ufs-3 it made a funny sound and the phone dead when l then try to flash it stops at flash id and l get the m-bus error:1f 00 10 40 00 04 00 01 01 2e bad mob ack.

[cell2cell]

and by the whay the phone did not power on like all dct 3 phones do when you connect to ufs the first time around

[RAMJAN_MOBILE]

change flah IC and flash mcu ppm,+rebuild imei+ui settings
10000% oky

[sej1234]

hello sir ,
i have a M-bus error when i flashing mobile then flashing is complete but flash Id register fail that time error display on screen m-bus error:1f 00 10 40 00 04 00 01 01 2e bad mob ack. similaraly UI setup fail & can not power on but when flashing only light on. so please advice me how to slove this prob.

[jamilshaikh5887]

1st Boot Ok, 2
2nd Boot Ok, DCT3, MAD: A1 G-01, ROM: 6, BUS: 16
FLID: 00200090,St M28W160T, Iw28f008.tia
Software:
Algorithm Ok, [C834]
Area: 0x00340000-0x003CFFFF Erased, Time: 00:09
MCU Flashing Completed, Time: 00:04
Area: 0x00340000-0x003CFFFF Erased, Time: 00:09
PPM Flashing Completed, Time: 00:04
Flashing Completed, Rebooting Mobile
Power Up / Init Local Mode Failed !
Flash Id Failed esId
Power Up / Init Local Mode Failed !
Mbus Error: epw e1 e3 e12
IMEI Rebuild Failed


plz help me brow

[tarsem20]

here is mbus error solution

only change the crystal ic, problem will be solved tested by me

[hossain ahmed]

re hot the cpu goodluck

[naim_007]

Brother Heat the flaseher Ic nd try again.