PDA

View Full Version : Savvy TCD168/CM-"Permanently blocked"-help!

Baza
03-12-2001, 05:06
to turn on quikly-phone full on...
andromeda 3.1 is freeze...
help-how unlock?&send soft on
chrysl@usa.net
ARS
03-12-2001, 21:21
on my site is flasher for savvy 128 and 168
file named savvyedit.zip
Baza
03-19-2001, 16:42
hello :(
:mad:
I try any EEPROM file...permanently blocked is not remove(tryed with out eeprom 24c32 and write on PonyProg)
I WRITE sending "mtelko" "SAVVY FREE"&"eep_tcd168ac144984.bin" file...
What with out eeprom?-my cable(standart FBUS)no may enter in TCD mode...
ReFLASH no may too.Push turn ON quickly-phone is full ON.
On forum - write how can modificate FBUS for correct work with philips phone...
i no understand how...
My phone is TCD168/CM locked to Beeline.
you may HELP?
slawek
03-19-2001, 19:36
Savvy cable is a standart Fbus cable but WITH external power !!

8 - RX
9 - TX
12 - GND

even "dead" phone should enter in TAT mode, using andromeda software you can reapir it by "repair" function and after by "unlock"

I repaired few Savvy ...
Slawek
Baza
03-19-2001, 22:58
Originally posted by slawek:
Savvy cable is a standart Fbus cable but WITH external power !!

8 - RX
9 - TX
12 - GND

even "dead" phone should enter in TAT mode, using andromeda software you can reapir it by "repair" function and after by "unlock"

I repaired few Savvy ...
Slawek


thank's
:rolleyes:
be test with external power :confused:
dup
03-19-2001, 23:02
from right to left !!!
first GND
four from philips to 10pin 232
five to philips to 9pin 232

with this wiring you can enter tat or flashing mode.

dup
Baza
03-20-2001, 09:10
:mad: :mad: :mad: :mad: :mad: :mad:
i connect to 15&16 pin MAX232-external power 5.5v(max for this chip)...
NOT WORK!
:rolleyes:
slawek
03-20-2001, 11:13
>i connect to 15&16 pin MAX232-external power 5.5v(max for this chip)...

???????????

are you crazy ??!?!
pin 15 of MAX is GND, pin 16 is +5V

check your email box for diagram.

Slawek
Baza
03-20-2001, 11:45
15...-
16...+
i am not crazy
:D
TITO
03-20-2001, 12:43
Hello Baza
To fix your problem you must to programing eeprom with programator and after that you need to flash phone.I been have some problem with 168/DP and all time after flashing phone say Permanentli Blocked.I read eeprom from 168/W7 AND PROGRAMING EEPROM IN MY 168/DP.After that I flash phone and phone work OK.
Pin out for SAVVY:
from right to left
pin1 gnd
pin4 TX
pin5 RX
If you need more helps mail me.
Tito
Baza
03-21-2001, 18:52
please send for me eeprom dump from 168/W7 ver.Have you scheme interface for Savvy? :rolleyes:
Mtelko
03-29-2001, 07:53
I repair it with this metod:
1. Flash phone with tcd_swup and Flash file for 168.

2. Phon say Permanently Blocked.

3. Start tcd_edit and read/write field 11 without changes. (This corect CRC)

4. Phone is live

Originally posted by Baza:
hello :(
:mad:
I try any EEPROM file...permanently blocked is not remove(tryed with out eeprom 24c32 and write on PonyProg)
I WRITE sending "mtelko" "SAVVY FREE"&"eep_tcd168ac144984.bin" file...
What with out eeprom?-my cable(standart FBUS)no may enter in TCD mode...
ReFLASH no may too.Push turn ON quickly-phone is full ON.
On forum - write how can modificate FBUS for correct work with philips phone...
i no understand how...
My phone is TCD168/CM locked to Beeline.
you may HELP?
Baza
03-29-2001, 10:20
ok :mad: :mad:
i have this solution :D thank's you too
MY CABLE NOT CORRECT WORKED FOR PHILIPS :rolleyes:

with siemens-work GOOD :o