View Full Version : plz check ASK/RPL CM CPU 622X IC FLASH SAMSUNG
halongmobile
03-25-2007, 12:46
check CM ASK/RPL CPU 622X _IC FLASH SAMSUNG
tranchiemtai
03-25-2007, 16:14
change FLash AMD, you will repair ok.
InfinitySupport
03-25-2007, 17:39
check CM ASK/RPL CPU 622X _IC FLASH SAMSUNG
It's good idea to make detailed problem description if problem really exist.
halongmobile
03-26-2007, 05:55
change FLash AMD, you will repair ok.
i can not open PHONE......
i can not open PHONE......
More easy way to get help:
no need to open phone
only describe here what is the problem and you will get answer how to solve your problem
I think his problem is:
Infinity can't repair the phone which uses Samsung KAD060300B flash rom.
P/s:With AMD/Spansion S71PL129JB flash rom,no problem at all.
Am I right @halongmobile? :-)
B/r
InfinitySupport
03-26-2007, 10:54
@hakima
It's really strange situation: we are trying to understand what is the problem instead of simply get detailed description like this:
1. problem is: .....
2. flash chip is: ....
3. problem only when: .....
etc.
First of all,sorry for misunderstanding.
I don't want to make a new thread with the same situation and that's why I post like that.
Here is my errors description:
I already tested some phone which has flash rom Samsung KAD060300B inside (MT6226 based).Phone can't be repaired after rebuild RPL file.So I decide to change flash rom with Spansion/Amd flash then rebuild with the same RPL(coz I did not change CPU so HW Id will not be changed).And after that,all of them were repaired.
I'm so sure all of those Samsung flashes have good condition coz they can be rewrite with Up 1024 prommer and work like a charm in (MT6217 CPU base).
At least,I hope you can understanding me now and will not think that I spamming and post bla..bla in your support forum.
B/r
InfinitySupport
03-26-2007, 12:49
@hakima
As about possible problems with flash chip.
It can be 2 possible problems:
1. flash chip dead/semi-dead (hardware fault, need to replace flash chip)
2. problem with correct flash chip detection (software problem)
in this case need to make this:
2.1. go to software "Settings" page and change "Advanced chip detection..." box on/off (check or un-check).
2.2. try now to write RPL again
if still no luck: post log here so I can check what is the problem and probably I'll give an advice what to do.
But for sure I can't give any advice if somebody say "problem exist with flash". What problem ? Where is the error ? What is problem reason ? Nobody know... So, I can't give exact advice in this case before I see detailed description.
halongmobile
03-27-2007, 10:25
@hakima
As about possible problems with flash chip.
It can be 2 possible problems:
1. flash chip dead/semi-dead (hardware fault, need to replace flash chip)
2. problem with correct flash chip detection (software problem)
in this case need to make this:
2.1. go to software "Settings" page and change "Advanced chip detection..." box on/off (check or un-check).
2.2. try now to write RPL again
if still no luck: post log here so I can check what is the problem and probably I'll give an advice what to do.
But for sure I can't give any advice if somebody say "problem exist with flash". What problem ? Where is the error ? What is problem reason ? Nobody know... So, I can't give exact advice in this case before I see detailed description.
U can not make ASK if ic flash SAMSUNG ( IC GOOD) U need log ???
InfinitySupport
03-27-2007, 10:39
@halongmobile
it's not hard for me to write the same one more time:
http://forum.gsmhosting.com/vbb/showpost.php?p=2340229&postcount=9
if still no luck: post log here so I can check what is the problem and probably I'll give an advice what to do.
tranchiemtai
03-27-2007, 16:46
I checked and repaired two mt 6226ba flash samsung.
actually when I flashed samsung I just only wrote until flash 1 ( infi detect 2 flash chip ) and it showed error and I couldnt continue write. you should use chinese miracle 1.20 write flash . After write rpl ok, you put the button call and power at the same time - it will be OK
This is Log.
COM3 selected
Device: Autodetect
Checking data, wait...
Action: Read information
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02]...
Release Power button now !
Boot Done
Initialize...
detecting chip[00] in region[00]...
flash: EC22E000000000
flash: 29EA0000000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: EC22E000000000
flash: 33AB6800000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
Initialize Done
Set baud...
921600
Set baud Done
Check space...
operation mode: Fast detection mode
device parameters autodetection in progress..
detecting chip[00] in region[00]...
flash: EC22E000000000
flash: 29EA0000000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: EC22E000000000
flash: 33AB6800000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: EC22E000000000
flash: 29EA0000000000
checking area[00000000]: 00000000-007FFFFF...
flash: EC22E000000000
flash: 33AB6800000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 01
eeprom area detected[00800000]: 00600000-007FFFFF
detect device identification, method #1...
detection phase #1...
protocol version: 0004
2nd [enhanced] (or higher) generation model detected
Attention: read full flash backup before any action !
warning: probably identification data damaged, power-on problem
possible
Probably identification data damaged,
id: [0BB51E29]
version: [M500TV_Y7_PCB01_GPRS_MT6226_S01.00_0.BIN_0ACB4A9D]
Do you want to write RPL file (RPL file must be in current folder) ?
flash: EC22E000000000
flash: 29EA0000000000
Write: rpl
rpl write ok
identification detection finished
device-id: 0BB51E29
version sw1: M500TV_Y7_PCB01_GPRS_MT6226_S01.00_0.BIN
version sw2: M500TV_Y7.00.0
detection phase #3...
.................................................. ..............
detect device parameters finished
detecting languages...
................................
Err: can't detect language parameter #1
can't detect language names
if software not respond/freez/failed now, make "Detect language names
(slow process)" unchecked and repeat operation.
file saved: backup_system_log_0BB51E29_
[M500TV_Y7_PCB01_GPRS_MT6226_S01.00_0.BIN]_0ACB4A9D_20070327-
181015.B0X.bin
Finished, time used: 138 sec
Remove/Install battery now !
COM3 selected
Device: Autodetect
Checking data, wait...
Action: Read information
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02]...
Release Power button now !
Boot Done
Initialize...
detecting chip[00] in region[00]...
flash: EC22E000000000
flash: 29EA0000000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: EC22E000000000
flash: F6811000000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
Initialize Done
Set baud...
921600
Set baud Done
Check space...
operation mode: Fast detection mode
device parameters autodetection in progress..
detecting chip[00] in region[00]...
flash: EC22E000000000
flash: 29EA0000000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: EC22E000000000
flash: F6811000000000
flash: AMD/Fujitsu std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: EC22E000000000
flash: 29EA0000000000
checking area[00000000]: 00000000-007FFFFF...
flash: EC22E000000000
flash: F6811000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 01
eeprom area detected[00800000]: 00600000-007FFFFF
detect device identification, method #1...
detection phase #1...
protocol version: 0004
2nd [enhanced] (or higher) generation model detected
Attention: read full flash backup before any action !
warning: probably identification data damaged, power-on problem
possible
Probably identification data damaged,
id: [6BEE1E9F]
version: [M503T_F5_PCB01_GPRS_MT6226_S01.00_0.BIN_ADE6B8AC]
Do you want to write RPL file (RPL file must be in current folder) ?
flash: EC22E000000000
flash: 29EA0000000000
Write: rpl
rpl write ok
identification detection finished
device-id: 6BEE1E9F
version sw1: M503T_F5_PCB01_GPRS_MT6226_S01.00_0.BIN
version sw2: M503T_F5.00.0
detection phase #3...
.................................................. ..............
detect device parameters finished
file saved: backup_system_log_6BEE1E9F_
[M503T_F5_PCB01_GPRS_MT6226_S01.00_0.BIN]_ADE6B8AC_20070327-
185203.B0X.bin
Finished, time used: 117 sec
Remove/Install battery now !
ask rpl exe dowloant link helpme ???????????
InfinitySupport
11-20-2008, 22:39
ask rpl exe dowloant link helpme ???????????
Hello,
Please, explain more detailed what you need to do.