lg kg200 help plz

[amiriratel]

hi team
i want unlock lg kg200 . it have mini usb port i connect it to my computer usb port and install lg modem driver and it connect with my computer with com 49
but when i want to unlock it with infinity and set port to com 49 . nothing happened for phone ans infinity says' s hold power on key..
how should i connect it to infinity software and unlock it ?

BR

[LordMen007]

use kg190/kg200 cable

for pinout
you can not use usb cable(thinx to mr mobileclinic)


Br
LordMen007

[IBMOBILES]

use kg190/kg200 cable

for pinout
you can not use usb cable(thinx to mr mobileclinic)


Br
LordMen007

hello can you gave complete pinout for this cable i mean infinty box side
1--------8
where is rx tx ground
please explain

[InfinityHelp]

hello!

box pinout you can find in our FAQ section:

box pin 2- tx
box pin 3- rx
box pin 8- gnd

phone connector pinout you can see in shell.exe selecting model LG KG200.
just connect box pins to correspondent pins on phone connector

[s1emens]

i use my own cable and i find it hard to connect the handset. is there anyway to easily connect it

i use mmodule 1.57
bau rate : slowest
baud autoselect checked
use advanced chip checked

br,
s1emens

[InfinityHelp]

hello!

must be cable fault

[s1emens]

I've searched the pinout it seems to be the same pinout for imobile 510/609/609i cable, am i right? Coz the cable i talked about is hand made, but without any resistor added. Let me try this 1st. That means no specific setting to make the connection easier right?

br,
s1emens

[InfinitySupport]

Yes, try imobile 510/609/609i cable. If it will not work justswap rx <-> tx wires.
Please, let me know about results.

[s1emens]

still not working, here is the log:
COM10 [VCP3] selected
Device: LG KG200
Checking data, wait...
Action: user code
unlock method: standard
Boot...
Press and HOLD Power button now !
baud autodetection active
9600
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 8 sec
Remove/Install battery now !

already swap rx/tx

try to short the rx with tip of the connector but still not working, is there any specific baud rate to ease the connection?

br,
s1emens

[s1emens]

finally here is the correct setting, use imobile 510 cable but swap rx/tx, baud rate 460800, tick the RTS DTS box, untick Advanced Chip, choose boot baudrate to 10
here is the log:

COM10 [VCP3] selected
Device: LG KG200
Checking data, wait...
Action: user code
unlock method: standard
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6219:8B02:8B01]...
MT6226MA detected
boot step size: 000A
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 98004900000002:29EA0000000000
flash: Toshiba TV00578002DABD T 8Mb
detecting chip #01 in region #00...
flash: 98004900000002:6F736F00000000
flash: Toshiba TV00578002DABD T 8Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Check space...
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [standard] (or higher) generation
protocol ver: 04
ver. sw1: ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7330TH-001-R1D.BIN
ver. sw2: 7S7330TH-001-R1D
ffs offset/size: 00E00000/00200000
reading [eeprom[ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7330TH-001-R1D.BIN]]...
file saved: backup_eeprom[ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7330TH-001-R1D.BIN]_20070902-171441.A3E.bin
flash: 98004900000002:29EA0000000000
Check space Done
Manipulation...
detection procedure, wait...
detection procedure completed
Manipulation Done
Finalization...
Finalization Done
Write...
flash: 98004900000002:6F736F00000000
Write: eeprom
Write Done
Finished, time used: 154 sec
Remove/Install battery now !

cheers,

br,
s1emens

[InfinitySupport]

@s1emens
Thanks a lot for information !

[imran tec]

finally here is the correct setting, use imobile 510 cable but swap rx/tx, baud rate 460800, tick the RTS DTS box, untick Advanced Chip, choose boot baudrate to 10
here is the log:

COM10 [VCP3] selected
Device: LG KG200
Checking data, wait...
Action: user code
unlock method: standard
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6219:8B02:8B01]...
MT6226MA detected
boot step size: 000A
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 98004900000002:29EA0000000000
flash: Toshiba TV00578002DABD T 8Mb
detecting chip #01 in region #00...
flash: 98004900000002:6F736F00000000
flash: Toshiba TV00578002DABD T 8Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Check space...
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [standard] (or higher) generation
protocol ver: 04
ver. sw1: ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7330TH-001-R1D.BIN
ver. sw2: 7S7330TH-001-R1D
ffs offset/size: 00E00000/00200000
reading [eeprom[ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7330TH-001-R1D.BIN]]...
file saved: backup_eeprom[ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7330TH-001-R1D.BIN]_20070902-171441.A3E.bin
flash: 98004900000002:29EA0000000000
Check space Done
Manipulation...
detection procedure, wait...
detection procedure completed
Manipulation Done
Finalization...
Finalization Done
Write...
flash: 98004900000002:6F736F00000000
Write: eeprom
Write Done
Finished, time used: 154 sec
Remove/Install battery now !

cheers,

br,
s1emens
i do it same and get same results bt phone is still power off whn i check onm supply it goes to 5 amp not power on help pls

[InfinitySupport]

@imran tec
I don't understand what is the problem. You must explain the problem well if you want to get correct answer.