Phoenix Problem!!!

[Pinkgsm]

Phoenix,,,,only flash problem...other propertys is work...

Error message...:

Flashing failed.

Error occured during the flashing procedure.

Low level error description:

C102: Boot start txd up fail
The phone doesn't set Flasbus TXD line low after the VCC is
switched on. This error is received also when the phone is not
connected to the prommer

HRESULT 0x8004c102 (-2147172094)

----------or--------------

Flashing failed.

Error occured during the flashing procedure.

Low level error description:

C101: Boot timeout fail
The phone doesn't set Flashbus TXD line high after the VCC
is switched on

HRESULT 0x8004c101 (-2147172095)


How i flash load...

pls help me...

best regards...

[Bph&co]

Hi,

Please check your service battery !

You need to use 100% original service battery to flash your phone
with FPS8.


BR , Alex

[X-Shadow]

Hello,

For 8310 and 6510, you need XCS-1 + FLA-22... I dont think it
is possible to flash these phones without using FLA-22 or
FLA-22 clone because FLA-22 adapter is not a direct connection
from FLS-4 or FPS-8 to phone... it contains many components
inside!

For 9210, you can connect directly to FLS-4 or FPS-8 if
you can find a 10-PIN RJ-45 connector (not usual 8-pin). You also
need to destroy a working battery so that you can tap the VBAT
and the BATGND to the phone .

For other phones, you cannot just make service batteries because
they use all 4 pins of battery (GND, BSI, BTEMP, VBAT) which is
controlled by the FLA-XX. These phones include 6310, 6310i,
8310, 6510...

So I think you are using H.K. clone cables which do not work
directly with your original NK device. You must buy a special
adapter (also clone) so that your cables will work with your
device. Or if you have money, then buy original leads like Alex
said.

Best Regards,
X-Shadow

[remle]

Hi,

X-shadow is right . Also, don't forget for the DCT-4 Vpp line is always used.
Sometimes the error you mentioned is caused by hardware problem. When error is "doesn't set Flasbus TXD line low after the VCC...." the problem maybe in UPP and when error is "doesn't set Flasbus TXD line high after...." then problem is in UEM.

Best regards

[Pinkgsm]

Thanks all...

What is Fps-8 pinout?

How to FLA-18's scheme?

or

How i doing 8310 data cable and normal battery with for Fps-8 8310 service cable ...?

best regards...

[John_Doe]

Originally posted by X-Shadow
Hello,

For 8310 and 6510, you need XCS-1 + FLA-22... I dont think it
is possible to flash these phones without using FLA-22 or
FLA-22 clone because FLA-22 adapter is not a direct connection
from FLS-4 or FPS-8 to phone... it contains many components
inside!

For 9210, you can connect directly to FLS-4 or FPS-8 if
you can find a 10-PIN RJ-45 connector (not usual 8-pin). You also
need to destroy a working battery so that you can tap the VBAT
and the BATGND to the phone .

For other phones, you cannot just make service batteries because
they use all 4 pins of battery (GND, BSI, BTEMP, VBAT) which is
controlled by the FLA-XX. These phones include 6310, 6310i,
8310, 6510...

So I think you are using H.K. clone cables which do not work
directly with your original NK device. You must buy a special
adapter (also clone) so that your cables will work with your
device. Or if you have money, then buy original leads like Alex
said.

Best Regards,
X-Shadow


well you dont need original full set cables

cables from Neelix II also support fps8 and fls-4
if you are interested drop a mail to these guys
i use also fps8 with those cables and work no problem

[Pinkgsm]

New Problem....)))

Error message....:

Flashing failed.

Error occured during the flashing procedure.

Low level error description:

A407: Security bad command error
Security processor (SMCU) returns bad command error. Activate Fps-8

HRESULT 0x8004a407 (-2147179513)

Box is active...

Yours for help thanks...

Best Regards...

[Bph&co]

Hi,

This is very bad :(((

One thing though - you won't need service battery for sure !

BR

[Bert]

Yeah Alex you are right! ;)

[Pinkgsm]

Hi all...

who send to me activation file (*****.in)...

please help me...

thanks all...

best regards...

[GlobalStar]

hi


try box Activation software