1110 flashing problem......

[sandeepmansa]

log is here...... flashing with ufs

1st Boot Err: Bad Resp DCT3, C3 D3 5
Cannot Detect Mobile Brand
1st Boot Ok, DCT4, UPP: 2201
2nd Boot Error: 2
Platform: 3, Error Data:
D3 72 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Process Failed, Repowering Mobile

[sandeepmansa]

if i doing flashing with MT Box .....

Phone is in: Phone is not responding, power on phone!
============= Set Flash mode for info =============
VBat is 3.98V

Vpp pin has 0.09V, Not Connected
Pins:
Mbus 0, Box Tx 1, Box Rx 0, Bsi 0
Boot...
Using Tx2 Data line.
Invalid response from RAP3 boot( cable problem/damaged RAP3 chip/damaged phone power circuit
============= Set FBus mode for info =============
VBat is 3.96V

Vpp pin has 0.78V, Not Connected
Pins:
Mbus 0, Box Tx 1, Box Rx 0, Bsi 0
Using Tx2 Data line.
Processing File: rh70_03.080
Boot...
FAILED TO BOOT PHONE!!!
Make sure that phone is connected.

[wasim ansari]

When ever i do flashing on 1110i, 1112, 1600 models i get contact service on the screen i tried flashing with UFS, JAF, UB but it did'nt help me please healp me where i'm doing mistakes.

[sandeepmansa]

When ever i do flashing on 1110i, 1112, 1600 models i get contact service on the screen i tried flashing with UFS, JAF, UB but it did'nt help me please healp me where i'm doing mistakes.


problem with the hardware ...make a heat on cpu . . . . .

[chealsea]

check the cable sir got experience once..i change the cable and it flash normaly..some cables readout at info but doesnt flash...just try it

[syl phone]

[quote=sandeepmansa;2547139]log is here...... flashing with ufs

1st Boot Err: Bad Resp DCT3, C3 D3 5
Cannot Detect Mobile Brand
1st Boot Ok, DCT4, UPP: 2201
2nd Boot Error: 2
Platform: 3, Error Data:
D3 72 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00


I THINK its flah ic problem reheat n try to again flash it by jaf or mtbox

[cellbizz]

[quote=wasim ansari;2547227]When ever i do flashing on 1110i, 1112, 1600 models i get contact service on the screen i tried flashing with UFS, JAF, UB but it did'nt help me please healp me where i'm doing mistakes.[/quo


At first U can give Information By UFS. U look PPM File Condition
If PPM file Condition Not Good, so when On it give contact service .
Erase By JAF (Full Erase) then Skip Erase when Flash (By JAF) and Write Good PM. U can Unlock. U can Get Result.
OK
Good Luck

[superbashir]

1110 hehp
1st Boot Err: Bad Resp UPP, 02 FF FF 72
1st Boot Err: Bad Resp DCT3, 00 D3 5
Rebooting Mobile

[wasim_b]

1st attach the cable with set tightly (cable terminal should be touch with pcb flash point.
2nd its hardware problem. i sure bcz i face this one often. thanx

[wolf_dz]

any chance for those phone ........ mean when this message appear
1st Boot Err: Bad Resp UPP, 02 FF FF 72
1st Boot Err: Bad Resp DCT3, 00 D3 5
what to do.

[LORKANOV]

any chance for those phone ........ mean when this message appear

what to do.

YOUR BOX CANT DETECT YOUR PHONE BEING FLASHED.
TRY ANY OF THE FOLLOWING:
1) REATTACHING CABLE.
2) HEAT FLASH IC
3) CHECK CONECTION TO BOX

[rk_grover77]

Reball the cpu if doesn't work change the cpu.I hv solve 2 times this type of problem.once on 1110 and once 1600.