Please send your problem here,of china phone!

[khurram_player]

i have china 5310 dead after usb port insert into only two min....
after two min heat up.
dead on meater reading stop on 33.0

[estadios]

Hi,

how can I load WAP & MMS settings on this phone.

I'm living Portugal and would like to have it set up for the above.

Joe.

[Unknown®]

Hi,

how can I load WAP & MMS settings on this phone.

I'm living Portugal and would like to have it set up for the above.

Joe.

contact ur operator for all settings then can send it automaticlly via message

B.R

[Unknown®]

i have china 5310 dead after usb port insert into only two min....
after two min heat up.
dead on meater reading stop on 33.0

Hello !!

Probaly u ınsert wrong cable to phone and now it have shortcut if phone is dead try to remove P.A and post ur result.

B.R

[eager28wow]

I have this CECT V180 dual SIM phone.The problem is that when I switch on the mobile with the SIM inserted it shows up the Welcome screen, says it's searching and it switches off.
When I switch on the mobile without the SIM, it shows the Welcome screen, says to insert screen and I have access to all menus without switching off.
I tried a Factory Default Reset but problem still persists.
What can I do without any tools?(Guess nothing)
IMEI:351656005233907
S/N:KB3108AB001390

I have downloaded MTK6.8 Edit. Can I use this software directly to the mobile to flash it?

[Unknown®]

Hello!!

just try to format your phone and post result.

B.R

[donnyi]

where can i find PA on the phone?

[Unknown®]

where can i find PA on the phone?

Pfo is on RF (Radio baseband )unit.

B.r

[estadios]

contact ur operator for all settings then can send it automaticlly via message

B.R

Yes thank you this I know, but they ask for the make & model of the phone, what do I tell them ? They don't have these phones here.

[khabass]

hello i have nokia n95 chines it turn off when network coming help me please

[Unknown®]

hello i have nokia n95 chines it turn off when network coming help me please


Hello!!

Try to change battery if same result format or flash your phone.

B.R

[malikasim]

hi sir thnk*** in advance i need flash file of ZTC ZT8860 2sim MT6226 samsung K5L2731M after format its dead..........im using spiderman 2.42+ plzzzzzzzzzzzzzzzzzz help me out thnk***xx again in advance

[Unknown®]

hi sir thnk*** in advance i need flash file of ZTC ZT8860 2sim MT6226 samsung K5L2731M after format its dead..........im using spiderman 2.42+ plzzzzzzzzzzzzzzzzzz help me out thnk***xx again in advance



Give me full name of ur set orjinal version flash file ?

B.R

[Knighteagle]

hello...i have a zxd 2gsm phone...without sim works fine..sim in, restarts...can u help

[Nosfe]

hi all the codes I got here are great beleave me I was lost till I found this forum now I understand more my M666 chinese phone and I love it but I can not connect the cell phone to the band in my country when I buy it it said that it was quad band including 850 but I can not get it to work, finaly someone told me to get into engineering mode but for this m666 will not work what work is: *#66*# factory mode
and I need to get to the band selection to change it. can anyone help me please...

[zhanglei5556]

hi all the codes I got here are great beleave me I was lost till I found this forum now I understand more my M666 chinese phone and I love it but I can not connect the cell phone to the band in my country when I buy it it said that it was quad band including 850 but I can not get it to work, finaly someone told me to get into engineering mode but for this m666 will not work what work is: *#66*# factory mode
and I need to get to the band selection to change it. can anyone help me please...
First check your model.Chinese phones,some models have 850M and some models hasn't 850m.good luck.

[stjsrilanka]

i buy Huayu G788 mobile phone i need to install some software i try with Java but it's not working please help me to find support software format which faltform running in this phone
and specification say it have GPRS and WAP 2 but i cant find that link is

http://cgi.ebay.com.sg/Cell-Mobile-Phone-TV-Out-Games-MP3-MP4-Camera-Unlocked_W0QQitemZ160250217725QQihZ006QQcategoryZ3 8331QQcmdZViewItem

please tell me which flatphone running and how to enable GPRShttp://www.theimageshare.net/upload/images/453369G788_05.gif
http://www.theimageshare.net/upload/images/453369G788_13.gif

[stjsrilanka]

Daer zhanglei5556 i see your online please contact me stjsrilanka@yahoo.com or stjsrilanka@hotmail.com

[the eraser]

how about iphoe CECT Q380 dead due to wrong charger inserted?

[harry5641]

about to install java on china mobile phone
--------------------------------------------------------------------------------

Requested Sir,
I have a SED AK-606 PDA china mobile phone. I download MTK MT6228 CPU USB Driver and China Mobile Pc suite and install both on pc. There after I open PCsuite MFC Apllication. On this application window I can see the 'Install Java On headset' button. But this button is not active, so I can't install Java on my mobile phone. How can I install the java app. on my mobile? pls...pls...pls...help me.

[rerasta]

Hi,
I have a ZT321-1 solar charge phone but with this problem:
"phone don't stay in stand-by mode".
After 5 second, phone turn automatically in operative mode searching network.
This cause 2 problems:
1) High battery usage (autonomy is only 2-3 hours without calling)
2) No network for 10 second when phone turn in operative mode from stand-by mode

Instead when I connect Phone to my pc with Usb cable, it work very fine without this kind of problem.

I need to format it or there's some other solution?


Thx for helping.

[Unknown®]

Hi,
I have a ZT321-1 solar charge phone but with this problem:
"phone don't stay in stand-by mode".
After 5 second, phone turn automatically in operative mode searching network.
This cause 2 problems:
1) High battery usage (autonomy is only 2-3 hours without calling)
2) No network for 10 second when phone turn in operative mode from stand-by mode

Instead when I connect Phone to my pc with Usb cable, it work very fine without this kind of problem.

I need to format it or there's some other solution?


Thx for helping.

Try to format or flash ur set probaly %90 ur problem will be solved.

[Alexander Abuti]

hi,
please help with unlockcord for motorola v171 imei: 010503004201308. it seams to be network locked and returns an INVALID SIM CARD messega even after a flash it. thanks in advance.

[rerasta]

Try to format or flash ur set probaly %90 ur problem will be solved.

I don't have box/device to format.
If I use Mtk Flash Tools... which cable I need to buy for formatting?
Like this http://www.moxa.com/product/NPort_U1110.htm ?

[tas666]

For the ones asking for Internet and MMS settings for any phone this page could be useful

http://phoneontherun.com/carriers_en.php


For directions on configuring the CECT P168 go to this page after you got the settings

http://cectp168recursos.blogspot.com/2008/03/como-configurar-internet-y-mms-en-el.html

[RKTOR]

the touch screen doesn't work, i reset the phone with factory settings. now when i turn the phone on I can't get rid of collaboration wizard??

Please HELP!!!

[rishabhsinghvi]

i need china mp4 convertor for china mobile Spreadtrum base cpu

[tkowsar]

hi,
please help with unlockcord for motorola v171 imei: 010503004201308. it seams to be network locked and returns an INVALID SIM CARD messega even after a flash it. thanks in advance.


plz post in correct section (Motorola ODM) also try to search button, you found answer.

[tkowsar]

I don't have box/device to format.
If I use Mtk Flash Tools... which cable I need to buy for formatting?
Like this http://www.moxa.com/product/NPort_U1110.htm ?


its a usb to com converter, can help you though you pc have no com port for use. it can't help you to flashing china phone.

maybe for flash china phone have no cable available in market.

but you can make it, by any usb to com ring tone cable. use search button for it (already posted) you found way how to make cable.

[tkowsar]

For the ones asking for Internet and MMS settings for any phone this page could be useful

http://phoneontherun.com/carriers_en.php


For directions on configuring the CECT P168 go to this page after you got the settings

http://cectp168recursos.blogspot.com/2008/03/como-configurar-internet-y-mms-en-el.html

many thanks to you for good share.

[tkowsar]

the touch screen doesn't work, i reset the phone with factory settings. now when i turn the phone on I can't get rid of collaboration wizard??

Please HELP!!!


you have 2 way-

1st, change touch panel, maybe its bad. also you can try to repair it here-
http://www.gsmhosting.com/vbb/showthread.php?t=562548

2nd is, or flash it with a new file so no need calebaretion screen, but don't format otherwise calebaretion screen come again.

try and post result.

wbr
tkowsar

[tkowsar]

i need china mp4 convertor for china mobile Spreadtrum base cpu


plz use search button, many many mp4 converter already posted in this section for china phone.

[irada]

plz post pcb, i have many type of flash file for this phone but all pcb not same so need to see pcb first.

N73 RM-170
CPU Name:MT6226
CPU Type:6226
CPU VER:8A02
CPU SW:8A01
flash type:[SPANSION] S71PL127N
flash ID:0001227E (22202200)

[kopsa2005]

i have china pda zt8380 when powering on it show 10% 20%030%40%........................99% THEN GO OFF
PLEASE HELP FOR ANY SOLUTION GOT INFINITY MULTI BOX.

[Unknown®]

the touch screen doesn't work, i reset the phone with factory settings. now when i turn the phone on I can't get rid of collaboration wizard??

Please HELP!!!

Try to flash ur set otherwise probaly ur touch screen is damaged need to change it with new.

B.R

[Unknown®]

i have china pda zt8380 when powering on it show 10% 20%030%40%........................99% THEN GO OFF
PLEASE HELP FOR ANY SOLUTION GOT INFINITY MULTI BOX.

Hello!!

Try to format or flash ur phone with same version ur phone have and post the result.

B.R

[tkowsar]

i have china pda zt8380 when powering on it show 10% 20%030%40%........................99% THEN GO OFF
PLEASE HELP FOR ANY SOLUTION GOT INFINITY MULTI BOX.


though its mtk cpu, can you try to format first.
though not solve and not mtk cpu 2nd try to full flash.

i hope may your problem will solve.

wbr
tkowsar

[Munir Memon]

Sir:
I Send to you a complete Detail of this modle Red Star Chines phone, Fault is phone Dead and required flash file of this Model& Need Help no any model number show it so kindly guide what i do.

Information is Attech

Thanks

==== log opened: [7/8/2008 9:10:51 PM] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.50
S/N: 35F6:010F
Wait...
Device: Autodetect 6205-6227 NOR
Done
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:8C64:2410
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 01227E22212200:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20080708-211606.B0E.bin
Finished, time used: 268 sec
Remove/Install battery now !




Opration Again:


flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 01227E22212200:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20080708-205529.B0E.bin
flash: 01227E22212200:FFFFFF00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: 01227E22212200:FFFFFF00000000
Finalization Done
Finished, time used: 235 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !




I think flash chip is : Amd AMDFujitsu std

[Unknown®]

Sir:
I Send to you a complete Detail of this modle Red Star Chines phone, Fault is phone Dead and required flash file of this Model& Need Help no any model number show it so kindly guide what i do.

Information is Attech

Thanks

==== log opened: [7/8/2008 9:10:51 PM] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.50
S/N: 35F6:010F
Wait...
Device: Autodetect 6205-6227 NOR
Done
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:8C64:2410
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 01227E22212200:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20080708-211606.B0E.bin
Finished, time used: 268 sec
Remove/Install battery now !




Opration Again:


flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 01227E22212200:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20080708-205529.B0E.bin
flash: 01227E22212200:FFFFFF00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: 01227E22212200:FFFFFF00000000
Finalization Done
Finished, time used: 235 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !




I think flash chip is : Amd AMDFujitsu std


Hello!!

Plz click read detailed info and post here the log ı whant to see it maybe ı can help you.

B.R

[chrismoto]

Hello,

How do I flash my mt6227 using my data cable and pc?

Chris

[zhanglei5556]

Hello,

How do I flash my mt6227 using my data cable and pc?

Chris
first u need make a flash cable.that pinouts need GND VCC TX RX.then fins a flash tool and do it.:D

[jaytrio]

sir

i need flash file for my n95 single sim

infinity or spiderman files...........

T6226_05C_PCB01_GPRS_MT6226_S01.B10_EFATRIS_V1217A .BIN

br

[jaad_stupido]

hi i got a problem regarding my n99i phone....if ever i connct it to any computer it only prompt the word charger connectd...i cannot access the 3 options....

[tkowsar]

hi i got a problem regarding my n99i phone....if ever i connct it to any computer it only prompt the word charger connectd...i cannot access the 3 options....

All china phone haven't this option to access com port, MMC, webcam.

also you can try to change your usb cable.

and though its before work ok with pc and not solve still after changing usb cable, last you can try to change your phone connector. sometimes its some of pin is broken.

[mithon]

Please send your problem here, I can help you to solve the question of software and hardware of Chinese phone

my problem automatic chairing please give me a salvation:D

[unais98]

pls change the flash IC :)

[tkowsar]

sir

i need flash file for my n95 single sim

infinity or spiderman files...........

T6226_05C_PCB01_GPRS_MT6226_S01.B10_EFATRIS_V1217A .BIN

br


can you post pcb picture and flash chip model name?

[tkowsar]

my problem automatic chairing please give me a salvation:D


maybe its mtk cpu phone.

so just try to change your power ic (maybe mt6305)

hope your problem will solve, don't forgate to post result.

[Unknown®]

sir

i need flash file for my n95 single sim

infinity or spiderman files...........

T6226_05C_PCB01_GPRS_MT6226_S01.B10_EFATRIS_V1217A .BIN

br

Hello!!
just give me 10 min for ur flash file ıam uploading it..

B.R

[Unknown®]

sir

i need flash file for my n95 single sim

infinity or spiderman files...........

T6226_05C_PCB01_GPRS_MT6226_S01.B10_EFATRIS_V1217A .BIN

br

Enjoy it:

DOWNLOAD (http://rapidshare.de/files/40014497/T6226_05C_PCB01_GPRS_MT6226_S01.B10_EFATRIS_V1217A _16m_En_Ru_Fr_Es_Id_Th_Ar.B0M.rar.html)

B.R

[zakira]

nokia 6300 nonet or nosirvice pls help meeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

[meranplus]

can you help me?


i need flash file for Infinity 6300r


"RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E"


thank you very much more power!

[rafzkie_24]

pls help......... i need flasfile like.........

firmware
ver. sw1: SZMI25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_24.B IN
ver. sw2: MAUI.06B.W07.24, 00000000
eeprom:
eeprom[SZMI25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_24.B IN]]


i need this flash file for my 6300 china phone

[Unknown®]

can you help me?


i need flash file for Infinity 6300r


"RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E"


thank you very much more power!

Give me10 min to upload it;)

B.R

[Unknown®]

can you help me?


i need flash file for Infinity 6300r


"RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E"


thank you very much more power!

here is ur file enjoy:
DOWNLOAD (http://rapidshare.de/files/40014966/RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E.rar.html)

[Unknown®]

can you help me?


i need flash file for Infinity 6300r


"RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E"


thank you very much more power!

here is ur file enjoy:;)
DOWNLOAD (http://rapidshare.de/files/40015121/CM_Nokia-6300-RM-127_SZMI25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_ 24_16m_En_Fr_Ar.B0M.rar.html)

[meranplus]

can u help me again the file R6300_03_0_5T03S1215 not working on my china phone 6300r

can you send me the orig firmware:

RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_4T03 S0829.



thanks you again

[Unknown®]

can u help me again the file R6300_03_0_5T03S1215 not working on my china phone 6300r

can you send me the orig firmware:

RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_4T03 S0829.



thanks you again
Take it;):
http://rapidshare.de/files/40015269/CM_Cect-6300R_RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_ 0_4T03S0829_16m_Ru_Fr_En_Th_Vn_Cn_Ar_Cn_Ar.html

[meranplus]

master u send me a wrong if i write just correct me?

THE FILE U SEND ME IS

MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_07_En.B0M

[Unknown®]

master u send me a wrong if i write just correct me?

THE FILE U SEND ME IS

MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_07_En.B0M

I thınk u write wrong plz check and write here.
B.R

[meranplus]

master you send me a wrong file the file u upload is:
MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_07_En.B0M



thats the file i download from you:)

[Unknown®]

master you send me a wrong file the file u upload is:
MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_07_En.B0M



thats the file i download from you:)

What do u whant plz write again

[meranplus]

i try your file ilove you mwuuaahhh thank you very much!:D

my problem is solve thank you again and again!!!

[Airwavesport]

Hello,
I am very new in this, but I have a Daxian x999+, and after installing Spb pocket plus ver 4 the phone rebooted but now the touch screen isn't working anymore.
I tried to hardware reset the phone but at the end I have to select power off on the touchscreen and thaat isn't working. Is there an other way to do a hard reset.
The phone is still accepting the synchronisation with windows.
Thanx very much.

[Unknown®]

Hello,
I am very new in this, but I have a Daxian x999+, and after installing Spb pocket plus ver 4 the phone rebooted but now the touch screen isn't working anymore.
I tried to hardware reset the phone but at the end I have to select power off on the touchscreen and thaat isn't working. Is there an other way to do a hard reset.
The phone is still accepting the synchronisation with windows.
Thanx very much.


Hello!!

You need to format or flash your phone with any tool no other solution at the moment.

B.R

[tipco mobiles]

pls sent chiana phone cods

[tipco mobiles]

Hello!!

You need to format or flash your phone with any tool no other solution at the moment.

B.R

pls helpe chinaphone formating cod

[tkowsar]

pls sent chiana phone cods

pls helpe chinaphone formating cod


have no code for format china phone, just use MTK tool and cable or use device.

[Unknown®]

pls helpe chinaphone formating cod

Hello!!

There is not format code for china phones at the moment u need to format it with any tool .

use search button for format tools its already posted many times.

B.R

[chrismoto]

Hello,

Which program/software can I use to flash my mt6227 dual sim phone using my data cable and computer.

Chris.

[Unknown®]

search forum already posted many times MTK flash tool.

B.R

[Airwavesport]

Thnx,
Ill try that, but as I said i'm very new to this, could somebody post a link for formatting the Daxian x999+.

Many Thnx
A.
I did try to search the forum but i'm still confused which tool to use

[Unknown®]

Thnx,
Ill try that, but as I said i'm very new to this, could somebody post a link for formatting the Daxian x999+.

Many Thnx
A.
I did try to search the forum but i'm still confused which tool to use

First can u tell me cpu type of ur set?

B.R

[Airwavesport]

First can u tell me cpu type of ur set?

B.R

TI OMAP850 200Mhz

Thnx

[Unknown®]

TI OMAP850 200Mhz

Thnx

No dear open your phone and check over cpu somethıng writes lıke MTK or Spreadtrum?

[abbasp]

q380 shortpls help,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

[Eugene1888]

Hi, do you have any software for MT6227 please?

[papoo]

China Phone Memory card Not Detected.

[harry5641]

about to install java on china mobile phone
--------------------------------------------------------------------------------

Requested Sir,
I have a SED AK-606 PDA china mobile phone. I download MTK MT6228 CPU USB Driver and China Mobile Pc suite and install both on pc. There after I open PCsuite MFC Apllication. On this application window I can see the 'Install Java On headset' button. But this button is not active, so I can't install Java on my mobile phone. How can I install the java app. on my mobile? pls...pls...pls...help me.

[Airwavesport]

No dear open your phone and check over cpu somethıng writes lıke MTK or Spreadtrum?

Hmmm... I don't see that, do I have to disasemble the phone?

On the inside behind the battery is written:
Daxian x999+
gsm - gprs
Imei: (a lot of numbers)
s:n szzy0806

then on another sticker some chinese words and:
02-7004-080638
x999+
T329APYCX809T8

I hope you can use this

Thnx
A

[Unknown®]

Hmmm... I don't see that, do I have to disasemble the phone?

On the inside behind the battery is written:
Daxian x999+
gsm - gprs
Imei: (a lot of numbers)
s:n szzy0806

then on another sticker some chinese words and:
02-7004-080638
x999+
T329APYCX809T8

I hope you can use this

Thnx
A

Yes to see cpu ınformation u need to disasemble it.

B.R

[Airwavesport]

Yes to see cpu ınformation u need to disasemble it.

B.R

Oeps !!! I have no clue on how to start this.
There are only 2 screws visable and then backside won't come off.
Is there no way to try smething else, I mean it doesn't work now.
I can contect it to usb, windows mobile 6 starts up, I can use the side buttons but just the touch screen isn't working.

thnx
A.

[harry5641]

I have a SED AK-606 PDA china mobile phone. I download MTK MT6228 CPU USB Driver and China Mobile Pc suite and install both on pc. There after I open PCsuite MFC Apllication. On this application window I can see the 'Install Java On headset' button. But this button is not active, so I can't install Java on my mobile phone. How can I install the java app. on my mobile? pls...pls...pls...help me.

[gsmindia]

hi,
following flash file is required

model is n89
dual sim with bluetooth and tf

bin file name is LC6225_GEMINI_PCB01_GPRS_MT6225_S00-LBA8001_8_5_1_0T01MO320_M510C.BIN

tried flashing with a couple of other flash files but no use.

b.r

gsmindia

[Nosfe]

I did review the cellphone look at this link please http://www.digitaltradings.com/best!seller/Product/M666/M666.htm it shows in detail the phone I have. I just need the engineering's code so I can set it up in the right band could you help me please.

[malikasim]

hi sir thnk*** in advance i need flash file of ZTC ZT8860 2sim MT6226 samsung K5L2731M (FREEBIRD_PCB01_GPRS_MT6226_S01.M908_V118_0501)aft er format its dead..........im using spiderman 2.42+ plzzzzzzzzzzzzzzzzzz help me out thnk***xx again in advance IM USING INFINITY AND SPIDERMAN 4.42+
FREEBIRD_PCB01_GPRS_MT6226_S01.M908_V118_0501

[tkowsar]

q380 shortpls help,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

china phone common shorted section-
1. charging section
2. power ic.
3. network rf and pa
4. ringer ic.


plz try remove them and post result.


wbr
tkoesar

[tkowsar]

Hi, do you have any software for MT6227 please?


what software you need, explain plz.

wbr
tkowsar

[tkowsar]

China Phone Memory card Not Detected.


try with that, and post result plz. though you can't solve, i will more try for you-


wbr
tkowsar

[tkowsar]

about to install java on china mobile phone
--------------------------------------------------------------------------------

Requested Sir,
I have a SED AK-606 PDA china mobile phone. I download MTK MT6228 CPU USB Driver and China Mobile Pc suite and install both on pc. There after I open PCsuite MFC Apllication. On this application window I can see the 'Install Java On headset' button. But this button is not active, so I can't install Java on my mobile phone. How can I install the java app. on my mobile? pls...pls...pls...help me.


you can install java app or games on you phone though its have java supported option. so first do confirm it, your phone support java.


also china pc suite not support all phone becoz its old version and still no update version published.

wbr
tkowsar

[asimasmi]

chania insert sim then restting

[Unknown®]

chania insert sim then restting

Hello!!

Just try to format your phone ;)

B.R

[jigarm]

Hi, Friends

I have a S3 mobile and when I open bluetooth there is a error " intilazing bluetooth wait a moment!" please give me some soultion

[jigarm]

Hi, Friends

I have a S3 mobile and when I open bluetooth there is a error " intilazing bluetooth wait a moment!" please give me some soultion

[jigarm]

Hi, Friends

I have a S3 mobile and when I open bluetooth there is a error " intilazing bluetooth wait a moment!" please give me some soultion at mjigar12@gmail.com

[tkowsar]

chania insert sim then restting


brother hare have 2 problem-
1. insert sim
2. restart.

first you can try to format, maybe your both or only restart problem will solve. though insert sim not solve after formating next you try to re-hot power ic carefully.

try and post result.

wbr
tkowsar

[tkowsar]

Hi, Friends

I have a S3 mobile and when I open bluetooth there is a error " intilazing bluetooth wait a moment!" please give me some soultion


yes br, 99% time format help me for this problem solve.

so try plz and post result.


wbr
tkowsar

(in the future not make multiple post for same things, otherwise you will punished for breaking Rules)

[virtue]

N73 china keypad and joystick line anyone have it?
can help share?

thanks in advance :)

[sneha]

can u areenge flash file for KISEN F3 SPD base cpu

[Moosani]

i need given picture full flash file 16 mb

http://rapidshare.com/files/130654032/n77.JPG.html

[tkowsar]

can u areenge flash file for KISEN F3 SPD base cpu


also need more info for help you, as like phone flash cpu model, chip name, etc

so post all details about your phone, i will try for you.


wbr
tkowsar

[renaissa]

N73 china keypad and joystick line anyone have it?
can help share?

thanks in advance :)


here is your solution-

[tkowsar]

i need given picture full flash file 16 mb

http://rapidshare.com/files/130654032/n77.JPG.html


post all info about your phone for correct flash file, otherwise wrong file kill your phone or phone is still dead after flash.


wbr
tkowsar

[Moosani]

what info u need i can post any thing

[samflash]

viruses for China phones. the message in boot scream is "slave verno Mismatch!" Please help me

[Unknown®]

viruses for China phones. the message in boot scream is "slave verno Mismatch!" Please help me

Hello!

plz format your phone if problem not solved just flash your phone and your problem will be solved.

B.R

[zahidshariff]

need pin out for china n73

[Unknown®]

need pin out for china n73

there is lot of various n73 witch pinout u need plz post ur pcb picture here

B.R

[pazeth™]

Hi zhanglei5556,

I need your assistant, I have a nokia 6300 china, it's restart with simcard. any solution?

Thank you for advice
cheers
pazeth

[tkowsar]

Hi zhanglei5556,

I need your assistant, I have a nokia 6300 china, it's restart with simcard. any solution?

Thank you for advice
cheers
pazeth


99% time this problem solved by phone format, so try plz and post result.


wbr
tkowsar

[malikasim]

hi sir thnk*** in advance i need flash file of ZTC ZT8860 2sim MT6226 samsung K5L2731M (FREEBIRD_PCB01_GPRS_MT6226_S01.M908_V118_0501)aft er format its dead..........im using spiderman 2.42+ plzzzzzzzzzzzzzzzzzz help me out thnk***xx again in advance IM USING INFINITY AND SPIDERMAN 4.42+
FREEBIRD_PCB01_GPRS_MT6226_S01.M908_V118_0501

[lucky_bmr]

heellllllllllo sir . i have chinese phone. model no . cect u90 touchlife . i have the problem of handsfree mode
.. general mode dooesnt aactivate

[jadmae]

pls help me i have a china phone model q380 the keypad not function

[tkowsar]

pls help me i have a china phone model q380 the keypad not function

plz see here-
http://www.gsmhosting.com/vbb/showpost.php?p=3477020&postcount=2

wbr
tkowsar

[tkowsar]

heellllllllllo sir . i have chinese phone. model no . cect u90 touchlife . i have the problem of handsfree mode
.. general mode dooesnt aactivate


check hands free socket in phone. though need change it.

also you can try with that-

[meranplus]

here is ur file enjoy:
DOWNLOAD (http://rapidshare.de/files/40014966/RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E.rar.html)



master can you pls send me a BOM. to be a firmware of Infinity


bec. i cannot flash the phone
" this is the file name you send to me"

CM_Cect-6300R_RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_ 0_4T03S0829_16m_Ru_Fr_En_Th_Vn_Cn_Ar_Cn_Ar


hope you can do it thanks:)

[meranplus]

can you send me the orig. firmware or write firmware for my phone

history *try to format no luck but successful all done but same problem the phone automatically turn off.

next step try to reprogram the phone the phone is dead

here is the log:

COM5 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:836A:EAD4
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
detecting chip #01 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
detecting chip #01 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
it's time to stop: 2B0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.3C4EE913.[RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_4T03 S0829.BIN_42792443].rpl
identification#1 detection finished
device-id: 3C4EE913
identification#1 protocol ver: 04
ver. sw1: RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_4T03 S0829.BIN
ver. sw2: R6300_03_0.4T03S0829, BCDB86BD
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 98004900000002:2BEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
detecting ffs structure pass 1...
...................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.............................................
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
detecting ffs structure pass 2...
...................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.............................................
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #2 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_3C4EE9 13_RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_4 T03S0829.BIN_42792443_20080715-123339.B0X.bin
Finished, time used: 176 sec
Remove/Install battery now !
Loading file v.02...
RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_5T03 S1215__ffs_01.B0E.bin loaded



hope master you can help me

[Unknown®]

master can you pls send me a BOM. to be a firmware of Infinity


bec. i cannot flash the phone
" this is the file name you send to me"

CM_Cect-6300R_RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_ 0_4T03S0829_16m_Ru_Fr_En_Th_Vn_Cn_Ar_Cn_Ar


hope you can do it thanks:)

Wİtch file u need write here plz and for witch tool?

B.R

[kopsa2005]

Please Help Need Flash File For China Nokia 5300i Slide For Infinity Or Multibox

[Unknown®]

Please Help Need Flash File For China Nokia 5300i Slide For Infinity Or Multibox

Post details about ur firmware.

B.R

[meranplus]

Wİtch file u need write here plz and for witch tool?

B.R


sir my box tools is infinity and i got the same files from infinity support

can you check this files if this is the same files i need for my phone 6300r

CM_Cect-6300R_RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_ 0_4T03S0829_16m_Ru_Fr_En_Th_Vn_Cn_Ar_Cn_Ar.B0M

RATECH26_06A_PCB01_GPRS_MT6226_S01.R6300_03_0_4T03 S0829__eeprom_01.B0E

[Unknown®]

Yes they are same flash files but one contains eeprom other doesnt.

B.R

[meranplus]

master thank you the phone 6300r is already finish and 100% working


thanks for guiding me:D

[Unknown®]

master thank you the phone 6300r is already finish and 100% working


thanks for guiding me:D

noproblem man every time welcome and also ıam happy to hear ur set is well.

B.R

[Moosani]

TYM072641_611_PCB01_GPRS_MT6226_S01[1].072641_611_V1221__Nokia-N77-2sim-2camera_16m_En_Ml.B0M


i need this firmware but 16 mb any format

[Unknown®]

TYM072641_611_PCB01_GPRS_MT6226_S01[1].072641_611_V1221__Nokia-N77-2sim-2camera_16m_En_Ml.B0M


i need this firmware but 16 mb any format

in 10 minutes ur firmware is comeing;)

[Unknown®]

TYM072641_611_PCB01_GPRS_MT6226_S01[1].072641_611_V1221__Nokia-N77-2sim-2camera_16m_En_Ml.B0M


i need this firmware but 16 mb any format

Here is your flash file;)

DOWNLOAD (http://gsmchevli.in/chinacloneflashfile/cgi-bin/CM_Nokia-N77-2sim-2camera_TYM072641_611_PCB01_GPRS_MT6226_S01.072641 _611_V1221_16m_En_Cn.B0M.bin)

B.R

[xxolaa]

hello!
I'd like to its help. you've got a zxn95 telephone there is not cable haply someone could the mother board pinout??

[tkowsar]

hello!
I'd like to its help. you've got a zxn95 telephone there is not cable haply someone could the mother board pinout??

post your motherboard/pcb picture here

[Munir Memon]

Dear :
Information is as given Kindly Note

COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:8C64:2410
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: 01227E22212200:FFFFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 01227E22212200:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
detecting ffs structure pass 1...
.....................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.................................................. ...
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
detecting ffs structure pass 2...
.....................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.................................................. ...
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #2 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
Finished, time used: 202 sec
Remove/Install battery now !



Thanks

[mhassanrazabj]

Hi To All: I Have A Lg Kg 3oo Mobile When I Press Power Button It Show Only Lg And The Power Off Plzzzzzzzz Help Me How Handle It
I Also Try To Format With Infinity And Ve Pro Boxes But Not Succeded


Thanks***xx

[tkowsar]

Hi To All: I Have A Lg Kg 3oo Mobile When I Press Power Button It Show Only Lg And The Power Off Plzzzzzzzz Help Me How Handle It
I Also Try To Format With Infinity And Ve Pro Boxes But Not Succeded


Thanks***xx


flash your phone br, i hope your problem will solve.

post result plz.

br
tkowsar

[thangtran84]

Could you please give me an advise? I want to change language support in China phone from English to Malaysia. Are The following step correct or not? :
1. Check Processor of the phone.:)
2. Connect the phone with PC. This step I don't know how to do:p. I don't know which communication is using, COM or USB; and also the software manage this connection.
3. Install a new OS which support Malaysia language for phone.Where can I find this new OS?:p
Thank you.

[mastmastguy1]

hi guyz , need help for s3+ , problem cannot save picture after capture


please help *#### not working

[nasagih]

Dear Sir,
Please help me i need pinout for n77 dual sim-bluetooth 18 pin. Cannot attach the image to this forum...said upload of file failed....always failed..

Tx

[ton1x]

please help,

Need spideran files nokla hb-E90+ Mtk CPU Cable L18A
file name:

MTK_ROMINFO_v5 HM558HB1_V2P9_JD5420_7670_SAM_PCB2P0.BIN

This is th Phone View:
http://soundasia.en.alibaba.com/product/200082408/203240079/Special_Mobile_Phones/HBE90__cool_flip_dual_screen_Bluetooth_FM_radio_mo bile_phone.html


Thank you.

[tkowsar]

Could you please give me an advise? I want to change language support in China phone from English to Malaysia. Are The following step correct or not? :
1. Check Processor of the phone.:)
2. Connect the phone with PC. This step I don't know how to do:p. I don't know which communication is using, COM or USB; and also the software manage this connection.
3. Install a new OS which support Malaysia language for phone.Where can I find this new OS?:p
Thank you.


you need-
1. device or special usb to com cable (not only usb which is supply with phone, use search button for cable schematics)
2. tx and rx
3. flash file (same version, which is original have in you phone but your won language supported)
4. must backup current flash file before flash with new file.


br
tkowsar

[tkowsar]

hi guyz , need help for s3+ , problem cannot save picture after capture


please help *#### not working


maybe your selected storage (phone or mmc) have not enough space for saving file.

so check them, and also can u try to do " Restore factory default"


br
tkowsar

[tkowsar]

Dear Sir,
Please help me i need pinout for n77 dual sim-bluetooth 18 pin. Cannot attach the image to this forum...said upload of file failed....always failed..

Tx


download Infinity pinout, here you found more n77 and bluetooth 18 pin pinout-

Infinity Pinout (http://rapidshare.com/files/131038103/infinityPinout-_Last.rar)

and need Net Firmwork 2.0 for run infinity pinout, here-

Net Firmwork 2.0 (http://rapidshare.com/files/96414942/Net_Firmwork_V2.0.rar)


try plz

br
tkowsar

[nasagih]

thank you sir.. I appreciate your reply. thanks will check and try

[sneha]

also need more info for help you, as like phone flash cpu model, chip name, etc

so post all details about your phone, i will try for you.


wbr
tkowsar


modle = KISEN F3
CPU=SPDTRUM or SPD 6600D

DUAL SIM samt time network

condition dead

it take 2 hours for flash reading & writing take 2 hours

befire that set is on & ask sequrity code i will try on VEPRO but set is dead after writing readed flash file

so help me

[Moosani]

@telemaster
thanks for uploading firmware for me but this one i alread have from infinity support

i need 16 mb flash file

[kdessen]

Hallo,
i have a little problem.
i search for my cell phone "Cect T200+".
but can i find the function "hands-free calling"

Can someone help me please. Which Button i must push.
Thanks kdessen

this is my Phone
http://exwang.cn/pic/%E9%91%AB%E6%B3%B0T200+3.jpg

[nasagih]

download Infinity pinout, here you found more n77 and bluetooth 18 pin pinout-

Infinity Pinout (http://rapidshare.com/files/131038103/infinityPinout-_Last.rar)

and need Net Firmwork 2.0 for run infinity pinout, here-

Net Firmwork 2.0 (http://rapidshare.com/files/96414942/Net_Firmwork_V2.0.rar)


try plz

br
tkowsar







Not match sir....
Any solutions please for n77 18 pin pinout??

Tx

[malikasim]

hi sir thnk*** in advance i need flash file of ZTC ZT8860 2sim MT6226 samsung K5L2731M (FREEBIRD_PCB01_GPRS_MT6226_S01.M908_V118_0501)aft er format its dead..........im using spiderman 2.42+ plzzzzzzzzzzzzzzzzzz help me out thnk***xx again in advance IM USING INFINITY AND SPIDERMAN 4.42+
FREEBIRD_PCB01_GPRS_MT6226_S01.M908_V118_0501

[tkowsar]

Not match sir....
Any solutions please for n77 18 pin pinout??

Tx


can you see it in pcb, sometimes it have on pcb anywhere as some "DOT"

so plz try.


br
tkowsar

[sonjaewook]

hello,how can I Flash the Lang pack of Koean into a samsung phone which was bought in China?

[tkowsar]

hello,how can I Flash the Lang pack of Koean into a samsung phone which was bought in China?


its original samsung or copy samsung?

clear it first.

[ismayil]

hello sir,
i have a v180 china phone. its touchscreen is not working. i resoldered the contacts. but still its not working. can i change the touch screen of this model? pls answer me.

[itnishantha]

hi zhanglei5556

I HAVE NOKLA N95(not tuch screen). its discharge the battry after 1/2 hour. batt is ok, Power ic is heating. how can i slow this problems. we havent buy any parts in sri lanka of china phone. please help me.

thanks
itnishantha@gmail.com

[sonjaewook]

its original samsung selled in Europe market,Thank you!

[sonjaewook]

its original samsung or copy samsung?

clear it first.



its original samsung selled in Europe market,Thank you!

[Unknown®]

hi zhanglei5556

I HAVE NOKLA N95(not tuch screen). its discharge the battry after 1/2 hour. batt is ok, Power ic is heating. how can i slow this problems. we havent buy any parts in sri lanka of china phone. please help me.

thanks
itnishantha@gmail.com

first try to change power ıc if doesnt help second replace pfo hope it will help you.

B.R

[Unknown®]

its original samsung selled in Europe market,Thank you!

if your phone is original samsung now you are in wrong section plz post your problem in samsung section.

B.R

[gniusmx]

I have phone K915 but only work in 900/1800 , is posible change this frecuency 850/1900 or make triban? 900/1800/1900.

Thanks

[Unknown®]

I have phone K915 but only work in 900/1800 , is posible change this frecuency 850/1900 or make triban? 900/1800/1900.

Thanks

To change your phone gsmband you need to play with phone hardware changeing some parts but this action need too much professional expert.

also its too hard on china phones bcz we dont have too much shematics etc. for all model and ı can just say to you forget it.

B.R

[YAYO85]

Please send your problem here, I can help you to solve the question of software and hardware of Chinese phone
please i have an i 9 and cant use the dual sim , please help me

[sneha]

what about me ?????????

modle = KISEN F3
CPU=SPDTRUM or SPD 6600D

DUAL SIM samt time network

condition dead

it take 2 hours for flash reading & writing take 2 hours

befire that set is on & ask sequrity code i will try on VEPRO but set is dead after writing readed flash file

so help me

:mad::mad::mad::mad::mad:

[fidmdoe]

what can i enter that 8digital after unlock vodafone? pls help

[shriram_sharma]

games in china mobiles,thems ,softwarer pls help me

[inayatowais]

i have some proble with s3 china phone ......problem is headest prfoiles is always activated plzzzzzzzzzzz help me its very argent ...........................................

[Unknown®]

i have some proble with s3 china phone ......problem is headest prfoiles is always activated plzzzzzzzzzzz help me its very argent ...........................................


Check headset connector clean it or try to change.

B.R

[nasagih]

Please sir need help..
I cannot read or format N73 china. The logs of spiderman as follows:

MTK open com 4 success!
Press on/off key please...
Target's hw code : 0x6226
Targert's sw ver : 0x8A01
Target's CPU UID : B9F57728
Get correct bootloader for target...
MTK AllInOne_DA_v3.0804.00
You can release on/off key!
[DA] Loading the 1st bootloader...
[BROM] fail to download DA!
[MTK] Close com 4 success!

The indicator of spiderman stopped at 76% always 76%...
What do I do sir???

[michaelwade3]

can someone give me a website to download a theme for a china phone?

[pf_114022]

china k770 sim not support halp pl............................

[Unknown®]

china k770 sim not support halp pl............................

Do u mean phone is simlocked or doesnt see simcard? plz explain your problem more.

B.R

[gsmsmile]

sir i have a problem with my cect N95 phone tuch screen is not working
ofter formating this still tuch screen any solution for this stage please

[sas-pc]

Please send your problem here, I can help you to solve the question of software and hardware of Chinese phone


mr.sir....

i hope that you can help me for this kind problem.
i recieve one mobile chines n95 2sim ang the big one,then when i make it read full flash, appers on sw display boot..press and hold power button now!
but when i press and hold it still no detection from the phone even i hold it half and hour stil the same answer,

about the pinout i follow the discription from the cable pinout.

sir what should i do for this kind probs, actualy i am first timer to used this kind sw!

thanks a lot!

[ps23fonecare]

i av a cect c6000+.which software can reset its passwords?

[tkowsar]

what about me ?????????

modle = KISEN F3
CPU=SPDTRUM or SPD 6600D

DUAL SIM samt time network

condition dead

it take 2 hours for flash reading & writing take 2 hours

befire that set is on & ask sequrity code i will try on VEPRO but set is dead after writing readed flash file

so help me

:mad::mad::mad::mad::mad:


long time not found reply,
because you not read this post-
http://www.gsmhosting.com/vbb/showthread.php?t=567883

br
tkowsar

[tkowsar]

please i have an i 9 and cant use the dual sim , please help me



why you can't use dual sim? explain details.

plz read this and post again-
http://www.gsmhosting.com/vbb/showthread.php?t=567883


br
tkowsar

[tkowsar]

what can i enter that 8digital after unlock vodafone? pls help


plz post your problem in correct section, may you will found solution.


br
tkowsar

[tkowsar]

games in china mobiles,thems ,softwarer pls help me


see here-
http://www.gsmhosting.com/vbb/showthread.php?t=563091


br
tkowsar

[tkowsar]

Please sir need help..
I cannot read or format N73 china. The logs of spiderman as follows:

MTK open com 4 success!
Press on/off key please...
Target's hw code : 0x6226
Targert's sw ver : 0x8A01
Target's CPU UID : B9F57728
Get correct bootloader for target...
MTK AllInOne_DA_v3.0804.00
You can release on/off key!
[DA] Loading the 1st bootloader...
[BROM] fail to download DA!
[MTK] Close com 4 success!

The indicator of spiderman stopped at 76% always 76%...
What do I do sir???


try with mtk tool and post result.

[tkowsar]

china k770 sim not support halp pl............................


read it carefully and post again-
http://www.gsmhosting.com/vbb/showthread.php?t=567883

[tkowsar]

sir i have a problem with my cect N95 phone tuch screen is not working
ofter formating this still tuch screen any solution for this stage please


better is change touch screen, may its damage.

also you can read this post for repair-
http://www.gsmhosting.com/vbb/showthread.php?t=562548

[tkowsar]

i av a cect c6000+.which software can reset its passwords?



mtk tool

use search button for it.

[mastmastguy1]

maybe your selected storage (phone or mmc) have not enough space for saving file.

so check them, and also can u try to do " Restore factory default"


br
tkowsar



hi mmc is selected i can store other items but not the camera clicked pictures.

[BAY-BD]

I have a chinese phone name MALATA.When i power on the phone only the name displayed and then power off otomaticly.I flashed it with Super Doctor box.But the problem is still same.Please help me.

[Unknown®]

I have a chinese phone name MALATA.When i power on the phone only the name displayed and then power off otomaticly.I flashed it with Super Doctor box.But the problem is still same.Please help me.

Can you post flash log here plz.

B.R

[tkowsar]

I have a chinese phone name MALATA.When i power on the phone only the name displayed and then power off otomaticly.I flashed it with Super Doctor box.But the problem is still same.Please help me.

you not post details, also i think its have nand flash.

so after full flash, format phone nand flash chip.


try and post result.

[tlnadar]

Sir can u please help me for all chines phone codes & hardware Diagram.

[tlnadar]

Sir please give me the Suggestion witch is the best software to flash all chines phones.

[tkowsar]

Sir can u please help me for all chines phone codes & hardware Diagram.


what is your problem? post you problem here.



Sir please give me the Suggestion witch is the best software to flash all chines phones.


find it by yourself

[mirochelle]

hi good day ...

pls , help me about my phone its iphone k808
the video doesnt play even 3gp format..
pls help me what im going to do ,, thank you very much;)

[Unknown®]

hi good day ...

pls , help me about my phone its iphone k808
the video doesnt play even 3gp format..
pls help me what im going to do ,, thank you very much;)

Hi plz use search button many many converter posted just try with them.

B.R

[X-Telemoveis]

Hello, i have a N95 cloned phone and i have two problems.

First my n95 is for one sim card only but two way slide like the original.

When i open the slide for the "media" side, to use bluetooth, file manager , etc i have a option that says audio player. When i tried to open this option the phone block for 5 seconds then goes to the "standy bye" menu and works all very good, but if i try again to open the "media" side I can't. I slide but doesn't show anything. I have to turn off the phone to work the media side again.

The other question is that i want to changue the language to Portuguese but i don't no how. Is possible to change the language whitout any box? Just USb cable and any program?

[Unknown®]

For first problem ı thınk formating phone will solve your problem.

for your second problem tochange language you need to find flash file with ur language if u cant find it there is language editor softs but this reqiure to need a box not free solution and you can edit ur phone flash file language and add any language with it.

Also post fully detail about your flash file ı will try to find it for you.

B.R

[sigamani]

i have sigmatel it is showing headphone simple help me...........................

[Unknown®]

i have sigmatel it is showing headphone simple help me...........................


Try to clean headset connector if doesnt help change it.

B.R

[sami_777]

Hi Friend I Want Pinout Of Chaina Mobile Model No St800 Techno

[nasagih]

try with mtk tool and post result.


I have tried also with MTK tool and the indicator stopped. Please any idea sir..??

[michaelwade3]

where can i download themes for my china phone coco v909 .. thank you ..

[Unknown®]

where can i download themes for my china phone coco v909 .. thank you ..


Use search button before asking already posted games themes -etc.

B.R

[nightmit]

i have cect u90 with headset symbol pl help me fast




thanks

[Unknown®]

i have cect u90 with headset symbol pl help me fast




thanks

open you phone and clean headset connector if doesnt help need to change it.

B.R

[gsm3_zaman]

Hi,
Can anyone solve my problem. ZTC ZT6618 ok set , i format it ok but the phone is deted help me

[Unknown®]

Hi,
Can anyone solve my problem. ZTC ZT6618 ok set , i format it ok but the phone is deted help me

did you get backup before formating if no post here ur phone flashfile details ı will try to give you.but if u backup ur flash before formatting only flash it ur problem will be solved.

B.R

[Eugene1888]

Try using ImTOO 3GP Video Converter 3 & choose 3GO for Blackberry.
I found my 3" tft Chinese phone is BS, it only plays 3GP for smaller format. I tried many converters, but this worked each time.
Send me a PM if you want hacked version of this converter.

[m.dande]

you take another mobile read flash file then flash 1000000000% ok

[Eugene1888]

Hi I haven't seen anything about this phone on the forum.
I think you'll get many enquiries as it's on eBay.

Anyway, it doesn't allow sim card, I think over 500 attempts and only twice did it authorise card, the rest of time I get the error in the image.

I've included a couple of pther image which will hopefully help you identify the phone.
When I connect to PC it finds harddisk - MT6227

Hope you have idea of what I can do or unlock code... I tried many codes found in your answers, only 1122 as phone pass worked. None of the others.

http://nordicimport.com/crapphone/DSCF3246.jpg

http://nordicimport.com/crapphone/DSCF3249.jpg

http://nordicimport.com/crapphone/DSCF3251.jpg

[Unknown®]

Hi I haven't seen anything about this phone on the forum.
I think you'll get many enquiries as it's on eBay.

Anyway, it doesn't allow sim card, I think over 500 attempts and only twice did it authorise card, the rest of time I get the error in the image.

I've included a couple of pther image which will hopefully help you identify the phone.
When I connect to PC it finds harddisk - MT6227

Hope you have idea of what I can do or unlock code... I tried many codes found in your answers, only 1122 as phone pass worked. None of the others.

http://nordicimport.com/crapphone/DSCF3246.jpg

http://nordicimport.com/crapphone/DSCF3249.jpg

http://nordicimport.com/crapphone/DSCF3251.jpg

Brother ı see ur phone is blocked by operator you need to change imei with any mtk tool use search button for tool and psot result.

B.R

[michaelwade3]

:)hi there mr. , i just wanted to ask where can i download themes for my cellphone coco v909 ... i really want to have themes.. thank you...:)

[Unknown®]

:)hi there mr. , i just wanted to ask where can i download themes for my cellphone coco v909 ... i really want to have themes.. thank you...:)

Try to use search button ı think it will help you.

B.R

[mohid shaikh]

sir, i have china cell sigmatel v88, outing going call is ok, but when anyone call it will show in miss call, is this format problem or anything else. pls reply

regards,
mohid

[Unknown®]

sir, i have china cell sigmatel v88, outing going call is ok, but when anyone call it will show in miss call, is this format problem or anything else. pls reply

regards,
mohid

Yes probaly, just try to format your phone and post result.

B.R

[mohid shaikh]

thanks brother

regards

mohid

[tkowsar]

can u help me
i have china mobile
vedio not sporat
vedio = .3gp"rawvedio you420p"
where the converter ?
plz help meeeeeeeeeeee sir


see here-
Rawvideo 3gp Converter (http://www.gsmhosting.com/vbb/showthread.php?t=569887)


future don't double post for same thing

[viickysp]

wher can i find china phone flash file latest.is ther any link pls post me viickysp@yahoo.com pllssss any one

[Unknown®]

wher can i find china phone flash file latest.is ther any link pls post me viickysp@yahoo.com pllssss any one

Witch file u need plz post here full details about ur phone ı will try to help you.

B.R

[toms4gsm]

Witch file u need plz post here full details about ur phone ı will try to help you.

B.R

Hi Telemaster,

Can you post arabic flash file for Fory TD 888?

[Unknown®]

Hi Telemaster,

Can you post arabic flash file for Fory TD 888?

Can you post details about ur flashfile plz?

[tamilkarthickbe]

when i change my battery after few minutes it will automatically switched off.and then it will on after few minutes. the total settings will be reseted.what i can do

[tamilkarthickbe]

how to connect GPRS via AIRTEl in sigmatel s3 .in s3 there is no option wap.there is any solution for that.

[fixed]

please help i cant detect the pin out of my n73 with cpu MT6226BA I HAVE MY SPIDERMAN CRACK AND PADFINDER FULLY ACTIVATED THE PROBLEM OF UNIT HANGS UP IF SIMCARD..

[khanmobiles0003]

sir when i connect and spay the phone vcc canot be detected and txd,rxd are connect vhen i remove the power cables
give me the best solution for spay the phone quicly

[bhatti_123]

this model chines
cect iphone
and i know all chines model charging cable sircut
my email id kaka.2022@yahoo.com:rolleyes:

[razorspells]

Hi, I have a China Phone TV70 and I have 3 questions regarding bluetooth and accessories.

1. Is there a way to send the sound of videos / TV and Radio to a bluetooth headphone. So far MP3 music can only be heard.

2. Is there an accessory that enables me to connect the phone to an external speaker? (Ex. usb to 3.5mm)

3. I have a 3.5mm bluetooth audio dongle but can't connect because the TV70 has a different usb type. Is there a solution to this so that I can connect it.

If anybody is selling this accessory or can build it. I'm willing to pay for it. Thanks!

http://www.razorspells.com/public/TV70.jpg

[mwitamasiaga]

Please send your problem here, I can help you to solve the question of software and hardware of Chinese phone

please help me i have NOKIA dubao 758 i need pin out thanks before

[tkowsar]

when i change my battery after few minutes it will automatically switched off.and then it will on after few minutes. the total settings will be reseted.what i can do


phone is on and setting reset, so what problem you face. write details.

[tkowsar]

how to connect GPRS via AIRTEl in sigmatel s3 .in s3 there is no option wap.there is any solution for that.


though you phone have internet support, you can do it manually to see other phone internet setting for same operator.

[tkowsar]

please help i cant detect the pin out of my n73 with I HAVE MY SPIDERMAN CRACK AND PADFINDER FULLY ACTIVATED THE PROBLEM OF UNIT HANGS UP IF SIMCARD..


though its your device/padfinder problem you can post it there support section.

and though you need pinout, post details about your phone, as like connector type, how many pin etc. i will try for you.

[tkowsar]

sir when i connect and spay the phone vcc canot be detected and txd,rxd are connect vhen i remove the power cables
give me the best solution for spay the phone quicly


though its for device problem, post your problem in there support section.

though need pinout, post details about your phone, i will try for you.

[tkowsar]

this model chines
cect iphone
and i know all chines model charging cable sircut
my email id kaka.2022@yahoo.com:rolleyes:

what is your problem? write details plz for found better help.

[tkowsar]

Hi, I have a China Phone TV70 and I have 3 questions regarding bluetooth and accessories.

1. Is there a way to send the sound of videos / TV and Radio to a bluetooth headphone. So far MP3 music can only be heard.

2. Is there an accessory that enables me to connect the phone to an external speaker? (Ex. usb to 3.5mm)

3. I have a 3.5mm bluetooth audio dongle but can't connect because the TV70 has a different usb type. Is there a solution to this so that I can connect it.

If anybody is selling this accessory or can build it. I'm willing to pay for it. Thanks!



post your problem in correct section HERE (http://www.gsmhosting.com/vbb/forumdisplay.php?f=163), you found solution.

and don't make 1 more post for same things.

br
tkowsar

[tkowsar]

please help me i have NOKIA dubao 758 i need pin out thanks before


try with these br, may your problem will solve-

[yanni4life]

Hey i have a C6000 phone , all i want know how to install Files with Jar format and meake it works on my phone
i installed that Spiderman thing but i did not understand how to do it :S
any help pls ?

[tkowsar]

Hey i have a C6000 phone , all i want know how to install Files with Jar format and meake it works on my phone
i installed that Spiderman thing but i did not understand how to do it :S
any help pls ?

see here-
http://www.gsmhosting.com/vbb/showthread.php?t=563091

[gsmplus]

i have problems with sanyo v801sa. in some apps, message si "retrieve nw info'. when i try to connect to retreive nw info, message is "fail to retreive nw info". my phone is working good, good signall,nice function but no internet for example. any suggestions? thanx in advance

[madhu91]

Pls help me . . .
I have got Sigmatel S3 phone . . .
My phone contacts are getting deleted once in 3 days when i try to change the battery and my profile is also getting resetted automatically . . . . could i pls get a solution for this ?

[RAVICELLCARE]

i have one n92 model china set it comes to me at rebooting complaind.i have veepro softwaree box. i formet the set it goes to dead.i packup the flash file at 16mb to flash the original packup file to the phone still now it is dead.what is the sollution for it.kindly reply to me.thank u MR.MY MAIL ID IS ravicellcare@gmail.com

[Unknown®]

Pls help me . . .
I have got Sigmatel S3 phone . . .
My phone contacts are getting deleted once in 3 days when i try to change the battery and my profile is also getting resetted automatically . . . . could i pls get a solution for this ?

Hello!!

this problem usally solved by formatting please format your phone with any Mtk tool and post result.

B.R

[Unknown®]

i have one n92 model china set it comes to me at rebooting complaind.i have veepro softwaree box. i formet the set it goes to dead.i packup the flash file at 16mb to flash the original packup file to the phone still now it is dead.what is the sollution for it.kindly reply to me.thank u MR.MY MAIL ID IS ravicellcare@gmail.com

plz follow these instructions:

* Erase Flash (16mb erase)

* Make format again

* Flash your phone with your backup.

I think your problem will be solved try and please post your result.

B.R

[scratched]

Hi, I got a Anycool d66+ as a gift. I try to config th GPRS Data, Wep, Internet and so on, but it doesent work. How can I do this My Sim is from Vodafone.
I get an instruction from dualsimhandy.net but its to complicated. Can you help me for that?
greetings Ralf

[murari_smartwok]

My CECT V 180 PDA Dual Sim starts restarting when I tried to transfer a file from another phone to my phone through Bluetooth. With SIM it starts restarting automatically . With out SIM it works OK. Any solution? Please help!!!!!!!!!!

[Unknown®]

My CECT V 180 PDA Dual Sim starts restarting when I tried to transfer a file from another phone to my phone through Bluetooth. With SIM it starts restarting automatically . With out SIM it works OK. Any solution? Please help!!!!!!!!!!

This problem can be solved by formatting just format your phone but dont forget to backup flash file before makeing any action.

B.R

[kdessen]

Hallo,
i have a ploblem.
I will edit my phonebook with PC. Can i read a phonebook-file from the mobile-phone with the PC. And then edit on the PC?
I have a mobile-phone from CECT T200+

Thank you for you answer
by kdessen

[rajesh_kuruvath]

china n95 memory cord not read, memory trey is good hoe it solve

[rubio]

- ERROR: DEVICE DAMAGED, NEED REBUILD!
Looking For AtMega32 ...Found
Test Device:
- Run Test 0 ...Ok
- Run Test 1 ...Ok
- Run Test 2 ...Ok
- Run Test 3 ...Ok
- MSG: DEVICE READY TO REBUILD!
Rebuilding Device:
- Write Flash ...Ok!
- Write Flash ...Ok!
- Write Flash ...Ok!
- MSG: NOT READY, PLEASE WAIT FOR PREPARE DATA!

[renesa]

is it possible to download a game to Chaina nokla mobile?

[Unknown®]

is it possible to download a game to Chaina nokla mobile?


Yes, just use search button games posted for china mobiles.

B.R

[fritz2003]

hi i need a manual english for china phone cect m1818 thanks

[madhu91]

Bros , How do that , Becos i am not at all having enough knowledge about these phones , Please help me...

[sneha]

long time not found reply,
because you not read this post-
http://www.gsmhosting.com/vbb/showthread.php?t=567883

br
tkowsar


modle = KISEN F3
CPU=SPDTRUM or SPD 6600D

DUAL SIM samt time network

condition dead

it take 2 hours for flash reading & writing take 2 hours

befire that set is on & ask sequrity code i will try on VEPRO but set is dead after writing readed flash file

so help me


http://mh33.com/attachment.php?aid=97236&noupdate=yes

http://mh33.com/attachment.php?aid=97237&noupdate=yes

here image

http://mh33.com/viewthread.php?tid=36248&highlight=KISEN%2BF3

here is te flash file but langqage problem

[mekz]

Hey guys,

I bought a Nokia 5310 for my wife, and when i put a sim card in there it will only show the Nokia startup screen then phone will switch off, if i take sim card out the phone works fine....also if i have sim card in there and power it up and when i see the Nokia startup screen i tap the power button again it will take me to the profile menu where i can choose "silent/headset/indoor etc" and the phone can then receive calls, but if i push back to exit that menu the phone again turns off...i dont have any special tools or box..i just have the phone and the USB cable it came with...is there anything i can do or should i throw this phone away?

P.S - i have tried connecting with USB but the drivers wont install and i have tried all of them.....

please any help would be great, my wife's bday is in a few days and this was her gift id love to have ti working before then!

[tkowsar]

Hey guys,

I bought a Nokia 5310 for my wife, and when i put a sim card in there it will only show the Nokia startup screen then phone will switch off, if i take sim card out the phone works fine....also if i have sim card in there and power it up and when i see the Nokia startup screen i tap the power button again it will take me to the profile menu where i can choose "silent/headset/indoor etc" and the phone can then receive calls, but if i push back to exit that menu the phone again turns off...i dont have any special tools or box..i just have the phone and the USB cable it came with...is there anything i can do or should i throw this phone away?

P.S - i have tried connecting with USB but the drivers wont install and i have tried all of them.....

please any help would be great, my wife's bday is in a few days and this was her gift id love to have ti working before then!

very sad!!!

read it and read 2 reference link in this post.

http://www.gsmhosting.com/vbb/showthread.php?t=567883

[mekz]

Sorry i dont understand?


very sad!!!

read it and read 2 reference link in this post.

[zhanglei5556]

modle = KISEN F3
CPU=SPDTRUM or SPD 6600D

DUAL SIM samt time network

condition dead

it take 2 hours for flash reading & writing take 2 hours

befire that set is on & ask sequrity code i will try on VEPRO but set is dead after writing readed flash file

so help me


http://mh33.com/attachment.php?aid=97236&noupdate=yes

http://mh33.com/attachment.php?aid=97237&noupdate=yes

here image

http://mh33.com/viewthread.php?tid=36248&highlight=KISEN%2BF3

here is te flash file but langqage problem


If it's software problem.pls try flash again by other CPF-BOX2.;)

[mynk]

hi kjadfouygzKAJPAFKUG

[sharon41]

I have a jincen phone with a MT6225 processor please send me a driver for vista for the communication port