Can't read any chinese phone ?????

[kasner]

COM4 selected
Device: Autodetect
Checking data, wait...
advanced flash detection active
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
921600
Set baud Done
Check space...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data Ok
identification data backup saved: id.83D39E41.[N618_PCB01_GPRS_MT6227_S01.1.BIN_EFA84486].rpl
identification detection finished
device-id: 83D39E41
protocol ver: 04
ver. sw1: N618_PCB01_GPRS_MT6227_S01.1.BIN
ver. sw2: N618.1
ffs offset/size: 00E00000/00200000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area detected[00000000]: 00E00000-00FFFFFF
reading [flash[N618_PCB01_GPRS_MT6227_S01.1.BIN]]...
error: data size mismatch: 001A5C00, retry...
error: data size mismatch: 00253800, retry...


I have this error for all china phones. What is wrong ?

TNX Kasner

[InfinitySupport]

1. use more slow connection, not 921600
2. don't use prolific-based cables
3. use high quality and so short as possible cables
4. error info that you is just a warning that it was an error during reading and software try to repair this error automatically.

[kasner]

1. use more slow connection, not 921600
2. don't use prolific-based cables
3. use high quality and so short as possible cables
4. error info that you is just a warning that it was an error during reading and software try to repair this error automatically.

OK. TNX . PB was solved with correcting of latency paremeters that was broken after installation PCI COM card based on MOSys chipset.

WBR Kasner

[Icemanoff]

COM47 selected
Device: Autodetect 6205-6227,6228 nor
Checking data, wait...
advanced flash detection disabled
Action: read NOR flash
Boot...
Press and HOLD Power button now !
Connecting, wait...
error: boot phase#2/1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 6 sec
Remove/Install battery now !

What's wrong???

[InfinitySupport]

@Icemanoff
It's cable problem, wrong pinout. You must use correct cable and select correct COM port.

Please, use "Cable Selector": http://forum.gsmhosting.com/vbb/showthread.php?t=398297
if not helps, please read: C:\Program Files\InfinityBox\pinout\ChineseMiracle.txt
if not helps, please read: http://www.gsmhosting.com/vbb/showpost.php?p=2212036&postcount=7