N80 reading error

[masterunlock]

i am trying to read flash chines miracle n80 fone.during the reading it's missing some areas pls check the log and suggest me is this readed flash is usefull or useless and why i can't read that area is some thing wrong.



COM7 selected
Device: Autodetect
Checking data, wait...
advanced flash detection active
Action: Read flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02]...
Release Power button now !
Boot Done
Initialize...
detecting chip[00] in region[00]...
flash: EC257E25082501
flash: 29EA0000000000
flash: AMD/Fujitsu std [0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
921600
Set baud Done
Check space...
operation mode: Fast detection mode
device parameters autodetection in progress..
detecting chip[00] in region[00]...
flash: EC257E25082501
flash: 29EA0000000000
flash: AMD/Fujitsu std [0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501
flash: 29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area detected[00000000]: 00E00000-00FFFFFF
detect device identification, method #1...
detection phase #1...
protocol version: 0004
2nd [enhanced] (or higher) generation model detected
Attention: read full flash backup before any action !
identification data Ok
identification data backup saved: id.B5A9FFE2.[YN60_HXT_V4_PCB01_GPRS_MT6227_S01.BIN_20BF2B2C].rpl
identification detection finished
device-id: B5A9FFE2
version sw1: YN60_HXT_V4_PCB01_GPRS_MT6227_S01.BIN
version sw2: YN60_HXT.6226.L10.F03.D9.C0.U4.V1.4
detection phase #3...
.................................................. ..............
detect device parameters finished
flash: EC257E25082501
flash: 29EA0000000000
reading [flash[YN60_HXT_V4_PCB01_GPRS_MT6227_S01.BIN]]...
error: checksum mismatch: 0004AC00, retry...
error: checksum mismatch: 000F7C00, retry...
error: checksum mismatch: 000FB000, retry...
error: checksum mismatch: 0015C400, retry...
error: checksum mismatch: 00214800, retry...
error: checksum mismatch: 00262C00, retry...
error: checksum mismatch: 00282000, retry...
error: checksum mismatch: 002CC800, retry...
error: checksum mismatch: 00421400, retry...
error: checksum mismatch: 004EDC00, retry...
error: checksum mismatch: 0073EC00, retry...
error: checksum mismatch: 007BE800, retry...
error: checksum mismatch: 007F1800, retry...
error: checksum mismatch: 0081D800, retry...
error: checksum mismatch: 0086E800, retry...
error: checksum mismatch: 00891800, retry...
error: checksum mismatch: 008F4C00, retry...
error: checksum mismatch: 00B32000, retry...
error: checksum mismatch: 00B95000, retry...
error: checksum mismatch: 00BAD400, retry...
error: checksum mismatch: 00CA1C00, retry...
error: checksum mismatch: 00CEB800, retry...
error: checksum mismatch: 00E4D400, retry...
error: checksum mismatch: 00E5BC00, retry...
error: checksum mismatch: 00F26800, retry...
error: checksum mismatch: 00F3B000, retry...
error: unexpected data: 1B3FDEA935
error: checksum mismatch: 00F64400, retry...
error: unexpected data: 1B3F
file saved: backup_flash[YN60_HXT_V4_PCB01_GPRS_MT6227_S01.BIN]_20070816-171430.B0M.bin
file saved: backup_system_log_B5A9FFE2_[YN60_HXT_V4_PCB01_GPRS_MT6227_S01.BIN]_20BF2B2C_20070816-171434.B0X.bin
Finished, time used: 625 sec
Remove/Install battery now !





B,r.

[InfinityHelp]

hello!

program will not save file with errors.
if file is saved- all errors was retryed and coorect information was recieved

[masterunlock]

Can you pleas check the log and tell me whats wrong in th reading flash.Bcoz the mobile is brand new and working well.

I just try to read flash.



B,r.