cable mtk work for infinity

[muhned]

hi
you can use cable mtk for infinity that detect com mtk for infinity and hold power

but i have problem seem me

COM8 [Serial2] selected
Device: Autodetect
Checking data, wait...
advanced flash detection active
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
error: no any expected answer
error: wrong answer[3B]
error: wrong answer[3B]
error: no any expected answer
error: no any expected answer
error: wrong answer[3B]
error: wrong answer[3B]: wrong answer after chip cfi request
error: no any expected answer
number of flash chip/regions detected: 00/01
error: unknown flash chip, operation aborted
In case of flash chip detection problem: on/off "Use advanced chip detection method" box.
Initialize Fail
Finished, time used: 60 sec
Remove/Install battery now !

what i do? i use advanced ship and without it but same problem

help me infinity team

[InfinityHelp]

hello!

what is phones state? looks like it is not working, because there is problem with flash IC detection. Try to re-solder flash IC and try again

[muhned]

thanks for reply

but i tried on phone anycool d66 the phone is restart with sim card and without sim card work

same problem

baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
error: wrong answer[3B]
error: no any expected answer
error: no any expected answer
error: wrong answer[3B]
error: no any expected answer
error: no any expected answer
error: wrong answer[3B]: wrong answer after chip cfi request
error: no any expected answer
number of flash chip/regions detected: 00/01
error: unknown flash chip, operation aborted
In case of flash chip detection problem: on/off "Use advanced chip detection method" box.
Initialize Fail
Finished, time used: 61 sec
Remove/Install battery now !

i work on chinese miracle 1.42

help

[InfinitySupport]

Hello,

it's problem with mtk cables. Please, don't use cables based on "prolific" usb-com converters.

[muhned]

i don't use cables based on "prolific" usb-com converters

what i do ?

[muhned]

hi

i check cable mtk it is work fine

i rried for Anycool d66 thee the phone is ok

but snice read full flash my pc is restart . why

[muhned]

hi

i check cable mtk it is work fine

i rried for Anycool d66 thee the phone is ok

but snice read full flash my pc is restart . why

[muhned]

hi

i check cable mtk it is work fine

i rried for Anycool d66 thee the phone is ok

but snice read full flash my pc is restart . why

[muhned]

helppppppppppppppppppppppppppppppppppppppppppppp

[InfinityHelp]

hello!

we did not get any complaints regarding bad work infinity+mtk before.
to make your case clear- please make regular com port cable and try to read flash. after this we will be able to decide if this is related with MTK or separate program bug

[wsw243]

hello can anyone plz post full schematics and info than how to build MTK based cable and did it possible that scanning pinout like in MTK box? Waiting for your kind response.

Kind regards,

Vicky

[mike67]

Hi Infinity Team

I Used Mtk Cable With Jaf Com Converter And Whenever I Press Power Switch My Pc Restarts .. Why Is That But I Also Noticed That These Cables Have Rj45 Pin 4 And 5 Tx And Rx Respectively And 7 And 8 Ground .. So They Will Not Work In Infinity Direct ,, Now Am Not Sure If These Are Multibox Cables Or Mtk Cables ... But Thats How The Pinouts Of Rj45 Are ...

Please Help How Can I Use These Cables Ininfinity ... If I Make An Adaptor With Infinty Compatible Will It Help And Also The Length Of Cable Will Become Long Does It Matter ?

Also Correct Me If I Am Wrong : Infinity Rj45 Pinout 2 Tx 3 Rx 7/8 Ground

[InfinityHelp]

hello!

MTK cables are not RJ45 compatable.
that means you have multibox cables.
you need to make convertor one side rj45 male, another rj45 female.
this converotr will keep GND pins (7,8) on they original places, but will transfer Tx, rx (2,3) to position 4 and 5.
lenght of cable will not give problems, just dont make it too long.

[mike67]

Thank you Infinity ... great support .. I have ZTE 225 Vodafone using Mini Usb Connector ,, any pinouts for that model please ,,,

[contraicuagio]

thanks for reply

but i tried on phone anycool d66 the phone is restart with sim card and without sim card work

same problem

baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
error: wrong answer[3B]
error: no any expected answer
error: no any expected answer
error: wrong answer[3B]
error: no any expected answer
error: no any expected answer
error: wrong answer[3B]: wrong answer after chip cfi request
error: no any expected answer
number of flash chip/regions detected: 00/01
error: unknown flash chip, operation aborted
In case of flash chip detection problem: on/off "Use advanced chip detection method" box.
Initialize Fail
Finished, time used: 61 sec
Remove/Install battery now !

i work on chinese miracle 1.42

help


I think you have same problem with me.
Solution : Change your power and when you run infinity don't run anything. Power >= 450w. Sr my eng is very poor

[mobileclinic]

Thank you Infinity ... great support .. I have ZTE 225 Vodafone using Mini Usb Connector ,, any pinouts for that model please ,,,

You can find zte 225 pinout in x:\Program Files\InfinityBox\pinout
Also I am posting here for you-
keyboard top
1..........8
1: phone Tx (RJ-45 pin-3)
2: phone Rx (RJ-45 pin-2)
3: Gnd
BR.
Ashok Garg

[muhned]

hi all
my pc is restart since read full flash with cable mtk

cable mtk not work with infinity ?

[aukonline]

How we can use mtk cable on infinity box .

can any body explain step by step..

Advance

Thanks a freind

[InfinityHelp]

hello!

run infinity soft, plug to comuter any cable you want and pick needed com port.
thats it

[gsm_wrold2007]

change ur pc and get another high speed pc or upgrade ur RAM ,don't use usb extention.

[roses_for_lover]

plz any who give me brief idea about the repairing of "UFS3" device.plz any who post me.

[.::koolfriend4u::.]

plz any who give me brief idea about the repairing of "UFS3" device.plz any who post me.


my dear junior buddy,

u r in a wrong area...post ur request in correct section and also in main, b4 u try to post ur request..read the forum rules & obey as it is..

good luck next time