so strange problem chines miracles

[stivubicco]

:confused:COM1 [Serial0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC22E200000000:29EA0000000000
flash: Samsung AMD/Fujitsu std [B 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: EC22E200000000:01AC0000000000
flash: Samsung AMD/Fujitsu std [B 0008x002000 007Fx010000] 8Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC22E200000000:29EA0000000000
flash: Samsung AMD/Fujitsu std [B 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: EC22E200000000:01AC0000000000
flash: Samsung AMD/Fujitsu std [B 0008x002000 007Fx010000] 8Mb
number of flash chip/regions detected: 02/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data Ok
identification data backup saved: id.83279E01.[M500TV_S103_PCB01_GPRS_MT6226_S01.00_0.BIN_C6D5EAA 2].rpl
New firmware detected: M500TV_S103_PCB01_GPRS_MT6226_S01.00_0.BIN
- make "Read detailed information, ask/rpl" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification detection finished
device-id: 83279E01
protocol ver: 04
ver. sw1: M500TV_S103_PCB01_GPRS_MT6226_S01.00_0.BIN
ver. sw2: M500TV_S103.00.0
ffs offset/size: 00800000/00200000
detecting eeprom area in 2 chip(s)...
flash: EC22E200000000:29EA0000000000
checking area[00000000]: 00000000-007FFFFF...
flash: EC22E200000000:01AC0000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00800000
Detected eeprom address is non-standard: 00800000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address[00800000] confirmed by user
detecting eeprom size...
eeprom size: 00800000
eeprom chip: 01
eeprom area: 00800000:00000000-007FFFFF
reading [eeprom[M500TV_S103_PCB01_GPRS_MT6226_S01.00_0.BIN]]...
warning: data size mismatch at 0x00888400, retry...
read error recovered
warning: data size mismatch at 0x00A15400, retry...
read error recovered
file saved: backup_eeprom[M500TV_S103_PCB01_GPRS_MT6226_S01.00_0.BIN]_20070924-181132.B0E.bin
flash: EC22E200000000:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
flash: EC22E200000000:01AC0000000000
Write Done
file saved: backup_system_log_83279E01_M500TV_S103_PCB01_GPRS_ MT6226_S01.00_0.BIN_C6D5EAA2_20070924-181235.B0X.bin
Finished, time used: 895 sec
Remove/Install battery now !

i was formatting ffs on this unit it give me this error and phone cant power on i flash eeprom phone come alive but in same condition that when i select tones phone reboot itself and i cant send msg only i can recieve:)

[InfinityHelp]

hello!

try to format FFS one more time, if will not help- reball and resolder flash IC.

[InfinitySupport]

@stivubicco
Also try to make this: select "safe format" method and make Format FFS in "safe" mode.

Also, please, send your backup_system_log_83279E01_M500TV_S103_PCB01_GPRS_ MT6226_S01.00_0.BIN_C6D5EAA2_20070924-181235.B0X.bin file and flash backup file to InfinityBoxSupport@gmail.com for future research.
Thank you !

[stivubicco]

thanx for rply and i will test and send replay coz i just receive one today with same model and give same error while formatting

[stivubicco]

COM1 [Serial0] selected
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6226:8A02]...
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: E553_Y1THAIRUARFRBT.01.1_26S01
Version: M500Z_05C_HW
warning: wrong packet checksum
warning: wrong packet checksum
warning: wrong packet checksum
199 of 211 items cleared
5 items remains
Finished, time used: 53 sec
Remove/Install battery now !

thanx ifinity team i flash eeprom from backup and phone come alive and i format ffs again in safe mode and phone was repaired and work.

my simple qestion to infinty support is this safe mode is more gud than compelete mode coz this compelete take much time than safe mode and does safe mode make backup.

thanx in advance

[InfinitySupport]

"Safe" mode can be useful in situations when software in "complete" mode can't detect eeprom address correctly.
Backup: better make backup in any case
what is better: better is mode that gives you good results. It depends on phone. F.e. in some cases (eeprom very serious damaged) it's impossible to make "safe" format and only "complete" is possible.

[stivubicco]

"Safe" mode can be useful in situations when software in "complete" mode can't detect eeprom address correctly.
Backup: better make backup in any case
what is better: better is mode that gives you good results. It depends on phone. F.e. in some cases (eeprom very serious damaged) it's impossible to make "safe" format and only "complete" is possible.

thanx a lote sir now i have become expact on that many thanx sir:):):)

[wisam_wa]

i have same problem i would tomorrow try to flash eeprom backup and then formaat in save mode i hope to alive my phone