View Full Version : Chinese Ztc Zt303 100% Procces Then Phone Off
I HAVE ZTC ZT303.
PHONE 100% PROCCES THEN OFF.
I DONE FLASHING & FFS FORMAT.
BUT PHONE NOT NORMAL ON
PLEASE HELP ME:confused::confused::confused::confused::confuse d::confused::confused::confused::confused::confuse d::confused:
kurdistan
09-26-2007, 13:10
you must read full flash from other hand that good hardware then write to it and after flashing if the phone not working make ask\rpl the phone must be worked if the phone not working after ask\rpl check hardware
kurdistan
09-26-2007, 13:10
you must read full flash from other hand (ZT303) that good hardware then write to it and after flashing if the phone not working make ask\rpl the phone must be worked if the phone not working after ask\rpl check hardware
you must read full flash from other hand (ZT303) that good hardware then write to it and after flashing if the phone not working make ask\rpl the phone must be worked if the phone not working after ask\rpl check hardware
COM3 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: write NAND flash
"format ffs" active
write: Firmware
skip: Customization
skip: Language Pack
skip: Eeprom
protocol ver: 04
ver. sw1: U6_PCB04_GPRS_MT6228_S02.U6V10B015.BIN
ver. sw2: U6V10B015
id-page Ok
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
chip-id: 0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
NAND: Hynix HY27XS08121M 512+16 32 pages, 66Mb
NAND id: AD76AD76
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:007600AD0076 [04200000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
921600
Set baud Done
Identification...
converting data...
done
protocol ver: 04
ver. sw1: U6_PCB04_GPRS_MT6228_S02.U6V10B19.BIN
ver. sw2: U6V10B19
ffs offset/size: 01700000/02900000
id-page Ok
nfi area detection finished: Ok
structure: 2nd [standard] (or higher) generation
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
write core area 1 of 2...
write core area 2 of 2...
formatting...
Write Done
Finished, time used: 296 sec
Remove/Install battery now !
SAME PROBLUM BRO PLS HELP ME
I Have Got Five Pcs For Same Problum
.::KHURRAM::.
09-26-2007, 16:58
I HAVE ZTC ZT303.
PHONE 100% PROCCES THEN OFF.
I DONE FLASHING & FFS FORMAT.
BUT PHONE NOT NORMAL ON
PLEASE HELP ME:confused::confused::confused::confused::confuse d::confused::confused::confused::confused::confuse d::confused:
You guys face this problem coz u dont read its full flash before formatting ffs and writing another firmware.now check with charged bettery.it will take 1 minute to power on.dotn use power supply.
InfinitySupport
09-26-2007, 22:54
@KASAM
here is detailed instruction, please, follow it step-by-step: http://www.gsmhosting.com/vbb/showthread.php?t=447277
amir2202
09-28-2007, 23:27
Please Help Me
I Need Pinout Cable For Zt303
InfinitySupport
09-29-2007, 15:22
Please Help Me
I Need Pinout Cable For Zt303
keyboard top
1.........12
1: Gnd
6: Tx
7: Rx
tririval
11-04-2007, 07:25
cannot find the similiar firmware....
phone:ZTC-ZT303
protocol ver: 04
ver. sw1: U6_PCB04_GPRS_MT6228_S02.U6V10B28.BIN
ver. sw2: U6V10B28
what firmware can i write to this phone????
thnaks
InfinitySupport
11-04-2007, 11:38
cannot find the similiar firmware....
phone:ZTC-ZT303
protocol ver: 04
ver. sw1: U6_PCB04_GPRS_MT6228_S02.U6V10B28.BIN
ver. sw2: U6V10B28
what firmware can i write to this phone????
thnaks
you can find similar firmware in support area: flashfiles\ChineseMiracle\_MT6228
please, before you flash your phone, make "read firmware" procedure before flashing and send backup_flash and backup_system_log files to InfinityBoxSupport@gmail.com
tririval
11-04-2007, 12:41
my phone loading 100 % then off....
try all the step but still same problem....
-full back up
-format ffs safe and complete
-then write U6_PCB04_GPRS_MT6228_S02[1].U6V10B21__En_Fr_Es_Indonesia_Vn_Ru_Th_Cn.B4M.bin
- after that phone still loading 100% then off
please maybe another solution????
ZTC 313 pinout need...............
devenleo
12-17-2007, 23:33
you can find similar firmware in support area: flashfiles\ChineseMiracle\_MT6228
please, before you flash your phone, make "read firmware" procedure before flashing and send backup_flash and backup_system_log files to InfinityBoxSupport@gmail.com
hi
even i am looking for the same file
there are other files in the support area. but they do not end with no. 28
ie: U6V10B28.BIN.
can the files currently present in the support area ie: 15, 18, 20, ...... be used insted.
InfinityHelp
12-18-2007, 02:59
hello!
make full backup of your existing firmware and then is safe to try 15, 18, 20.
if they will not work properly- you can always return phone to original state by writing back your backup
dannyogolo
12-19-2007, 16:51
This thread starter is correct.
These phones with 6228 CPU with 100% Process Fault (as he calls it) dont repair even after flash.
FFS formatting dont work.
Unless its hardware fault (but the customers tell us it happened maybe during music or file transfer by Bluetooth, etc)