plz help infinity team "error: unexpected answer

[brain00000]

OM3 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read NAND flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
chip-id: 0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
NAND: Samsung K9F1G08X0M 2048+64 64 pages, 132Mb
NAND id: ECF18015
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100800015 [08400000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
115200
Set baud Done
Identification...
converting data...
done
protocol ver: 04
ver. sw1: SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN
ver. sw2: SHINEC_S2_IL9221_V2.2
ffs offset/size: 02000000/06000000
id-page Ok
nfi area detection finished: Ok
structure: 2nd [enhanced] (or higher) generation
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
identification data damaged
identification detection finished
error: unexpected answer:
warning: probably errors exist during flash read operation
Finished, time used: 294 sec
Remove/Install battery now !

[Chennairam]

NAND: 00EC:00F100800015 [08400000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
115200
Set baud Done


May Be that flash is not suported i think

[InfinitySupport]

@brain00000
double check your cable, make wires so short as possible, charge battery completely and try again.
waiting for results

[brain00000]

Team u r Great
Team u r Great
Team u r Great
i have solved my problem. not in above mentioned phone but i have rebuiled imei by cutting wire too short. but u did not advice me that point in my other thread " rebuild imei" u r great team and infiity box also,
thanks keep it up

[brain00000]

what i do. i have requested u about flash fiels through Email.
OM3 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read NAND flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
chip-id: 0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
NAND: Samsung K9F1G08X0M 2048+64 64 pages, 132Mb
NAND id: ECF18015
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100800015 [08400000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
115200
Set baud Done
Identification...
converting data...
done
protocol ver: 04
ver. sw1: SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN
ver. sw2: SHINEC_S2_IL9221_V2.2
ffs offset/size: 02000000/06000000
id-page Ok
nfi area detection finished: Ok
structure: 2nd [enhanced] (or higher) generation
identification data Ok
identification data backup saved: id.27EADFDB.[SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN_B202C57C].rpl
New firmware detected: SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN
- make "Read detailed information" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification detection finished
error: unexpected answer: 00
warning: probably errors exist during flash read operation
file saved: backup_nand_[SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN]_full_20071015-110243.B4M.bin
file saved: backup_system_log_27EADFDB_SHINEC28_06A_PCB04_GPRS _MT6228_S02.SHINEC_S2_IL9221_V2_2.BIN_B202C57C_200 71015-110247.B4X.bin
Finished, time used: 240 sec
Remove/Install battery now !