stivubicco
10-15-2007, 11:59
am very proud of infinty coz i receive one dead chines phone dead after fail to format by infinty i just read its model on pcb board and find flash file from support ans flash it and phone is alive again all thanx to infinty model is cect 668
COM7 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization
skip: Language Pack
skip: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom area
Do you want to use standard eeprom address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard eeprom address selected by user
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area: 00000000:00E00000-00FFFFFF
reading [eeprom]...
file saved: backup_eeprom_20071015-120733.B0E.bin
flash: EC257E25082501:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data damaged
identification detection finished
Area: Firmware
flash: EC257E25082501:29EA0000000000
Write: Firmware
structure: 2nd [enhanced] (or higher) generation
identification data damaged
identification detection finished
device-id: BA6F0F82
protocol ver: 04
ver. sw1: E519_Y_PCB01_GPRS_MT6226_S01.00_1.BIN
ver. sw2: E519_Y.00.1
ffs offset/size: 00800000/00200000
warning: invalid identification, ask/rpl calculation reqired
Probably identification data damaged,
device id: BA6F0F82
firmware version:
E519_Y_PCB01_GPRS_MT6226_S01.00_1.BIN_5B8BC7F5
RPL file must be in folder: C:\Program Files\InfinityBox\ChineseMiracle\
You can create RPL from ASK via client/server right now and press YES.
Do you want to write RPL file now ?
flash: EC257E25082501:29EA0000000000
flash: EC257E25082501:29EA0000000000
Write: rpl
rpl write ok
Write Done
Finished, time used: 1901 sec
Remove/Install battery now !
COM7 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization
skip: Language Pack
skip: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom area
Do you want to use standard eeprom address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard eeprom address selected by user
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area: 00000000:00E00000-00FFFFFF
reading [eeprom]...
file saved: backup_eeprom_20071015-120733.B0E.bin
flash: EC257E25082501:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data damaged
identification detection finished
Area: Firmware
flash: EC257E25082501:29EA0000000000
Write: Firmware
structure: 2nd [enhanced] (or higher) generation
identification data damaged
identification detection finished
device-id: BA6F0F82
protocol ver: 04
ver. sw1: E519_Y_PCB01_GPRS_MT6226_S01.00_1.BIN
ver. sw2: E519_Y.00.1
ffs offset/size: 00800000/00200000
warning: invalid identification, ask/rpl calculation reqired
Probably identification data damaged,
device id: BA6F0F82
firmware version:
E519_Y_PCB01_GPRS_MT6226_S01.00_1.BIN_5B8BC7F5
RPL file must be in folder: C:\Program Files\InfinityBox\ChineseMiracle\
You can create RPL from ASK via client/server right now and press YES.
Do you want to write RPL file now ?
flash: EC257E25082501:29EA0000000000
flash: EC257E25082501:29EA0000000000
Write: rpl
rpl write ok
Write Done
Finished, time used: 1901 sec
Remove/Install battery now !