View Full Version : nokia 6708 (chinies miracle)
astana2007
10-17-2007, 11:31
I need pinouts for nokia 6708 (chinies miracle)
InfinitySupport
10-17-2007, 18:43
Due to a lot of different models with the same name but absolutely different hardware,
bottom connectors and different pinouts we recommend you to include the next info:
1. detailed description of model
2. phone CPU chip name
3. phone PCB photo (Rx/Tx/Gnd test-points may exist on phone PCB)
4. attach phone photo
5. attach phone bottom connector photo
6. include information about Gnd and Charge pins on phone bottom connector
After you have this information prepared, check the next detailed description how to get pinout for your model:
use "Cable Selector": http://forum.gsmhosting.com/vbb/showthread.php?t=398297
if not helps, please read: C:\Program Files\InfinityBox\pinout\ChineseMiracle\
if not helps, please read: http://www.gsmhosting.com/vbb/showpost.php?p=2212036&postcount=7
if not helps, please read: http://www.gsmhosting.com/vbb/showthread.php?t=433447
astana2007
10-17-2007, 19:23
Thanx sir,inside the set rx and tx given .
its my 1st chinies and also 1st set to operate with infinity please give me some more instructions.
set auto restart.
what should I do now.
ful flash or some short cuts available like formatting etc.
InfinitySupport
10-17-2007, 19:26
my best advices:
1. it's always good idea to read threads at top of forum: http://www.gsmhosting.com/vbb/showthread.php?t=447277
2. never be lazy, try to make SEARCH before ask question !
3. never be lazy, read sticky threads before ask !
4. never be lazy just because nobody like lazy ppl !
astana2007
10-18-2007, 10:22
sir still no luck.I found rx and tx but set is not showing any connection with device
Here is logs
COM1 [Serial0] selected
Device: Autodetect
Checking data, wait...
advanced flash detection active
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
I select format ffs
InfinityHelp
10-18-2007, 12:40
hello!
is tx and rx points is marked on PCB? please write which point you connected to which Box rj45 pin
astana2007
10-18-2007, 14:28
red cable for TX
yellow for RX
black and brown for ground
TX and RX r marked on pcb
InfinityHelp
10-18-2007, 14:39
hello!
swap with places red and yellow wires and try again
astana2007
10-18-2007, 14:48
Alredy checked with this method
but still no luck
InfinityHelp
10-18-2007, 15:02
hello!
red and yellow wires goes to pin2,3 of RJ45 ?
astana2007
10-18-2007, 15:11
yes u r right.
I select
2 no. cable red for tx
3 no. cable yellow for rx
and then I checked to replace the position of both cables but no luck
InfinityHelp
10-18-2007, 15:16
hello!
in some phones there is 2 pair of tx and rx.
marked like tx_a, rx_a, tx_b, rx_b
do you have second pair of data pins?
astana2007
10-18-2007, 15:53
there is no second pair of RX TX
InfinityHelp
10-18-2007, 16:25
hello!
what type system connector have this phone?
astana2007
10-18-2007, 16:38
hello!
what type system connector have this phone?
Here is system connector