waiting for file Y500_PCB04_GPRS_MT6228_S02.Y500V10_06_52_V1_3T08D0 70510.BIN]_full_20

[rajman2500]

Thanks for file, we will try to prepare and upload good file in
support area ASAP.

Try to charge battery with external power supply and make "format ffs"
let me know about results.

--
Best regards,
IHelper

Tuesday, October 16, 2007, 5:49:05 PM, you wrote:


IBST> ----- Original Message -----
IBST> From: raj man
IBST> To: support@infinity-box.com
IBST> Sent: Tuesday, October 16, 2007 4:36 PM
IBST> Subject: backup chinese phone


IBST> hi
IBST> i am sending u backup file of chinese phone DVD
IBST> back label is in chineses language DVD 500 gsm gprc + log file

IBST> COM8 [VCP0] selected
IBST> Device: Autodetect 6228 NAND
IBST> Checking data, wait...
IBST> Action: read NAND flash
IBST> Boot...
IBST> Press and HOLD Power button now !
IBST> baud autodetection active
IBST> 19200
IBST> Connecting, wait...
IBST> Initializing[6228:8A02:8A02]...
IBST> chip-id: 0000:0101
IBST> boot step size: 0400
IBST> Release Power button now !
IBST> Boot Done
IBST> Initialize...
IBST> version: 3.1
IBST> NAND id: ECF10095
IBST> page size: 800+40
IBST> pages/block: 40
IBST> bits i/o: 08
IBST> address cycles: 04
IBST> blocks: 0400
IBST> ram size: 00800000
IBST> NOR: 0000:000000000000 [00000000]
IBST> NAND: 00EC:00F100000095 [08400000]
IBST> warning: NOR flash chip not supported or not detected
IBST> Initialize Done
IBST> Set baud...
IBST> 115200
IBST> Set baud Done
IBST> Identification...
IBST> converting data...
IBST> done
IBST> protocol ver: 04
IBST> ver. sw1:
Y500_PCB04_GPRS_MT6228_S02.Y500V10_06_52_V1_3T08D0 70510.BIN
IBST> ver. sw2: Y500V10.06.52.V1.3T08D070510
IBST> ffs offset/size: 02000000/06000000
IBST> id-page Ok
IBST> nfi area detection finished: Ok
IBST> structure: 2nd [standard] (or higher) generation
IBST> file saved:
backup_nand_[Y500_PCB04_GPRS_MT6228_S02.Y500V10_06_52_V1_3T08D0 70510.BIN]_full_20071013-194027.B4M.bin

IBST> problem with this phone is hang on boot and now its dead but i
made a backup


i tried to format in safe mode but giving me this error

COM8 [VCP1] selected
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6228:8A02]...
Connecting, wait...
error: can't finalize test moide
Operation failed !
Finished, time used: 21 sec
Remove/Install battery now !

waiting for the file
thanks

[rajman2500]

hi infinity team please tell how much time will it take


thanks
rajmna

[InfinityHelp]

hello!

please try to format FFS not in Safe, but in complete mode.
safe mode require set to be powered ON.
please dont forget to hold Power button pressed until software asks to release it

[rajman2500]

OM8 [VCP1] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: NAND reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
chip-id: 0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
NAND id: ECF10095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100000095 [08400000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
115200
Set baud Done
Identification...
converting data...
done
protocol ver: 04
ver. sw1: Y500_PCB04_GPRS_MT6228_S02.Y500V10_06_52_V1_3T08D0 70510.BIN
ver. sw2: Y500V10.06.52.V1.3T08D070510
ffs offset/size: 02000000/06000000
id-page Ok
nfi area detection finished: Ok
structure: 2nd [standard] (or higher) generation
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
Write Done

after flashing and complete format set is still dead

thanks
rajman