Need Eeprom Flash File Of Itel It600

[saniamirza]

DEAR FRIENDS,
I HAVE A ITEL 600 IN DEAD CONDITION WHEN I TRY TO FORMAT THIS THEN IT SHOWS THAT
COM3 selected
Device: Autodetect 6205-6227,6228 NOR
Checking data, wait...
advanced flash detection active
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03]...
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 98004900000002:01AF0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 98004900000002:01AF0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
.
detection phase #2...
.................................................. ..............
warning: identification information not found, possible reasons:
.old firmware type w/o identification data
.damaged firmware
.damaged hardware
detect device parameters finished
detecting eeprom area in 1 chip(s)...
flash: 98004900000002:01AF0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 00000000
Detected eeprom address is non-standard: 00000000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address[00000000] confirmed by user
error: critical error#1 during eeprom size detection
error: can't detect eeprom address/size
error: autodetection failed
Finished, time used: 30 sec
Remove/Install battery now !

I THINK THE EEPROM FILE IS CORRUPET.

THANKS IN ADVANCE FOR ANY SOLUTION.

[InfinitySupport]

You must flash this phone with firmware file but not with eeprom.
Also it may be hardware damaged phone, f.e. dead or bad soldered flash chip.

[saniamirza]

You must flash this phone with firmware file but not with eeprom.
Also it may be hardware damaged phone, f.e. dead or bad soldered flash chip.


Dear sir ,
i have read the full flash before format ffs ,but when i try to flash the phone with this flash file than it shows the same error that i was given in first post.
Secondly i tried to flash the phone which i download from support area,but when i try to select the flashfile then it is not show in firmware selection.sir please tell me how to select the firmware file.

[saniamirza]

You must flash this phone with firmware file but not with eeprom.
Also it may be hardware damaged phone, f.e. dead or bad soldered flash chip.


Dear sir ,
i have read the full flash before format ffs ,but when i try to flash the phone with this flash file than it shows the same error that i was given in first post.
Secondly i tried to flash the phone which i download from support area,but when i try to select the flashfile then it is not show in firmware selection.sir please tell me how to select the firmware file.
Thanks in advance and sorry for my english.

[InfinityHelp]

hello!

sorry, can you explane step by step what you doing and at what point you get problem?