View Full Version : Be5 No Credit
HI
i got a be5 v 123 ( wap ) Flash Type : Fujitsu 4MB . And when i insert sim card and try to dial it will display : Out of credit . Credit your card . i think the IMEI is barred cause when i insert other provider sim the mobile will work . Is there any IMEi changer around ?
thx in advance
mp3hot
1 st problem is solved , had Billing On , i resetted the billing system and now it went off . but i still need a IMEI changer cause its not letting me call or recieve calls . Its displaying ; Service is not available .
thx
I got another be5 but v 121 , if i copy its data and write it on the v123 would it work ?
thx
mp3hot
Send me flash area 4000-6000.
Mailto to josif@takas.lt
Read phone data with "Alcatel BE5, 4 "LOTO" repair by Vygis v1.2" in file **.pdt. If 32b s/z not corupted I test help you.
HI
I managed to kill the Alcatel BE5 phone , i tried to flash phone with v121 and the programme ( Alcatel Toolbox by emsi ) crashed whilst erasing the flash . i rebooted the PC and when i tried to connect to the mobile it says " Sending Boot ... ERROR " is it possible to recover this mobile ?
thx
mp3hot
[QUOTE]Originally posted by mp3hot
[B]HI
I managed to kill the Alcatel BE5 phone , i tried to flash phone with v121 and the programme ( Alcatel Toolbox by emsi ) crashed whilst erasing the flash . i rebooted the PC and when i tried to connect to the mobile it says " Sending Boot ... ERROR " is it possible to recover this mobile ?
For BE5 phones and EMSI soft you have to push "connect" button twice (after "connection error" dont disconect. Just push connect again).
[QUOTE]Originally posted by mp3hot
[B]HI
i got a be5 v 123 ( wap ) Flash Type : Fujitsu 4MB . And when i insert sim card and try to dial it will display : Out of credit . Credit your card . i think the IMEI is barred cause when i insert other provider sim the mobile will work . Is there any IMEi changer around ?
I have same problem (no credit, recharge your card).But other 4 cards works fine.The phone was from D1.
Originally posted by pavlin
[QUOTE]Originally posted by mp3hot
[B]HI
I managed to kill the Alcatel BE5 phone , i tried to flash phone with v121 and the programme ( Alcatel Toolbox by emsi ) crashed whilst erasing the flash . i rebooted the PC and when i tried to connect to the mobile it says " Sending Boot ... ERROR " is it possible to recover this mobile ?
For BE5 phones and EMSI soft you have to push "connect" button twice (after "connection error" dont disconect. Just push connect again).
U didnt understand me , i got a alcatel BE 5 v 123 and i tried to flash it to V121 . When it was erasing the flash it got stuck and i booted up the computer now it fails to read the mobile . So now i cannot flash it back to v123 and the mobile is killed . is there any possibility to make this Alcatel live again?
mp3hot
GSM Deals
07-08-2002, 02:58
What about some BE5123 wap having toshiba flash chip i've killed one.cause flash is protected or actual flasher need loader
for this kind of chip
for flashing your phone just use be5 repairer "Kody.exe" first read phone and save PDT file then for test upload the saved file if upload succeded (if not do not try flashing i'm sure it'll become a toy )then flash phone with other version then upload pdt file again
to solve "verify smart card"message
regards
To mp3hot:
Did you trie to flash the phone w/o read? What soft did you use?
Originally posted by pavlin
To mp3hot:
Did you trie to flash the phone w/o read? What soft did you use?
No i didnt try to flash the phone without reading it , i m using Alcatel Toolbox by EMSI v.1.015b ( free version ) > what software do u suggest me to use ? and where can i d/load it .
thx mp3hot
Originally posted by mp3hot
No i didnt try to flash the phone without reading it , i m using Alcatel Toolbox by EMSI v.1.015b ( free version ) > what software do u suggest me to use ? and where can i d/load it .
thx mp3hot
I use the same soft. It works fine for me (except the case of protected flash).
petregsm
03-16-2006, 20:02
please, i need v123 for BE5. from where i can downloads?
thanks my frieds
hi
anybody have the BE5 OT500 key pad schematic
pls reply me on my email
sarfaraz9999@gmail.com
thanx