View Full Version : cect q610 n72 small copy
smartengg
11-28-2007, 10:34
i need cect q610 copy of n72 pinouts. it has 1*12 charging socket. rx,tx is also mentioned on pcb but not working.... checked on two phones.
InfinitySupport
11-28-2007, 11:57
Due to a lot of different models with the same name but absolutely different hardware (f.e. exist at least 5 phones with name "Chinese Nokia-N95" but different pinouts),
bottom connectors and different pinouts we recommend you to include the next info:
1. detailed description of model
2. phone CPU chip name
3. phone PCB photo (Rx/Tx/Gnd test-points may exist on phone PCB)
4. attach phone photo
5. attach phone bottom connector photo
6. include information about Gnd and Charge pins on phone bottom connector
After you have this information prepared, check the next detailed description how to get pinout for your model:
use "Cable Selector": http://forum.gsmhosting.com/vbb/showthread.php?t=398297
if not helps, please read: C:\Program Files\InfinityBox\pinout\ChineseMiracle\
if not helps, please read: http://www.gsmhosting.com/vbb/showpost.php?p=2212036&postcount=7
if not helps, please read: http://www.gsmhosting.com/vbb/showthread.php?t=433447
smartengg
11-29-2007, 14:21
the pinouts described by infinity help for cect q610 is CECT_Q610 /(18 pin)
3:GND
9:RX
10:TX
but charging socket is 1*12 with 9th pin ground
plz give some other solution.............
InfinitySupport
11-29-2007, 18:01
the pinouts described by infinity help for cect q610 is CECT_Q610 /(18 pin)
3:GND
9:RX
10:TX
but charging socket is 1*12 with 9th pin ground
plz give some other solution.............
Hello,
Please, read my previous message in this thread very carefully.
infinity help for cect q610 is CECT_Q610 /(12 pin)
InfinityHelp
11-30-2007, 20:29
hello pukhraj!
do you have test points marked on PCB? try to connect with them.
@smartengg: try again with test points marked on PCB.
please note: Tx point on PCB must be connected to Rx pin on box (pin3)
and otherwise Rx point on PCB must be connected to Tx pin of box (pin2)
smartengg
12-01-2007, 12:26
hello pukhraj!
do you have test points marked on PCB? try to connect with them.
@smartengg: try again with test points marked on PCB.
please note: Tx point on PCB must be connected to Rx pin on box (pin3)
and otherwise Rx point on PCB must be connected to Tx pin of box (pin2)
i have tried it but no responce from phone......
InfinitySupport
12-01-2007, 18:18
i have tried it but no responce from phone......
Hello,
If phone can't be detected by software this means that pinout is wrong or phone hardware damaged.
jainmunda
12-01-2007, 20:16
i tested on 3 pcs but not working tx rx are mentioned on the pcb but not working
Hello Infinity Supporter
CECT Q610 (Market N72 On Screen)
1.......12
{.............}
Pinout Marked on pcb not work
pls tell correct pinouts
InfinityHelp
12-04-2007, 13:09
hello!
did you try to swap wires on PCB pinout?
because like i told already phone Tx must go to box Rx and otherwise phone RX to box Tx.
some of users connect Tx to Tx, Rx to Rx- that is why cable is not working
sselectronics
12-22-2007, 23:07
Hello I tried all connections on pcb but no resultes
Mine is CECT Q610 N72 SMALL WITH 1*12 CONNECTOR AND 5TH PIN IS GROUND FROM KEYBORD TOP POSITION PLEASE HELP
Gurpreet_singh
01-20-2008, 16:06
same problem with me
arunamobile
01-20-2008, 19:40
Hello I tried all connections on pcb but no resultes
Mine is CECT Q610 N72 SMALL WITH 1*12 CONNECTOR AND 5TH PIN IS GROUND FROM KEYBORD TOP POSITION PLEASE HELP
Dear
please see phone motherboard first this phone is not mtk this is infinion so infinity not support this your pinout is right but no support of this processer so you cant do with infinity
Aruna Export