Make Chinese phones cable for Infinity from Ve-pro cable!

[BruceLeo]

Hi!
I use RJ45 and cable set from Ve-pro box for my work.

And this is "How to make it?"

1. Make RJ45 cable with pinout from infinity-box with 3 wire : TX, RX and GND.
http://rapidshare.com/files/75989178/DSC00013.JPG.html
2. Use Ve-pro box (or SuperDoctor Box...) for scan pin for your phone (TX, RX and GND).
3. Connect RJ45 cable to 24 pin connector (come with Ve-pro cable set).
http://rapidshare.com/files/75989468/DSC00014.JPG.html
4. Connect ve-pro cable to 24 pin connector.
http://rapidshare.com/files/75989756/DSC00016.JPG.html
5. Connect ve-pro cable to phone.
http://rapidshare.com/files/75990006/DSC00015.JPG.html
6. Start software and enjoy.....
I tested on many phones and software working very good with baurate 921600.
:D
"COM4 [VCP2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
chip: 0031:F829:0CB0
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 Ok
security area backup saved: id.E6755D04.[V860_D8_PCB01_GPRS_MT6226_S01.SUM_TP_VISUS_VG5183. BIN_94A99DE4].rpl
New firmware detected:
V860_D8_PCB01_GPRS_MT6226_S01.SUM_TP_VISUS_VG5183. BIN

- make "Repair security area" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
device-id: E6755D04
identification#1 protocol ver: 04
ver. sw1: V860_D8_PCB01_GPRS_MT6226_S01.SUM_TP_VISUS_VG5183. BIN
ver. sw2: V860_D8.SUM.TP.VISUS_VG5183
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
flash: EC257E25082501:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
flash: EC257E25082501:29EA0000000000
Write Done
file saved: backup_system_log_E6755D04_V860_D8_PCB01_GPRS_MT62 26_S01.SUM_TP_VISUS_VG5183.BIN_94A99DE4_20071212-123617.B0X.bin
Finished, time used: 290 sec
Remove/Install battery now !"