Aclatel 311 Dead By Angelo Soft !!

[makona]

hi friend ,
plz i need help with this...

i tried to unlock this phone with angelo unlocker ver 1.02 ..
first i got backup of eeprom zone and simlock data ..

i repaired 1 phone before when it was logger only !
so i decided to use it ..

phone is dead after press ( unlock ) and operation finished .

then i re_tried connect to phone with it but " phone not respond .. check battery and cable "

i tried with old logger er 1.04 many times then it can read phone ..
i did open locked log and write to phone but said " this filenot for this phone ..or...etc "

so , i pressed " disconnect and reset logger "

after this

i can't connect to phone using any free tool
i tried angelo many times ... old logger and unnlocker 1.02
, Anjel Final , Cosmo , BFU and mobitel ..

all " PHONE NOT RESPOND " !!

cable is 100% working .. i have 511 can read it easy by cable .
battery is charged ( it was 100% working before kill it )

plz don't tell me u muust write full flash from...etc !!!

my problem is !!

CAN'T CONNECT PHONE TO PC AFTER ANGelO KILLED IT !

HELP PLZzzz and Thanks v.much

[razor]

Beside me was a similar problem!Try change parameter for comport (for instance 9600).After use 311remote v.1.2 (loger by Angelo) !Press button "connect" and several times press button "C" or "hand up/down".Unless it was got, that replace the battery , and repeat!If programm detect phone (even with mistake) try to flash phone ,with Omegaflasher, right fullflash with other such alcatel and flash eeprom zone with your phone!!!!! Sorry for bad bad english!!!! :)

[dusan.g]

I've got a dead 311 and the same problem - I can't connect to the phone. Cable is correct (tried it on 511), battery is full. I've got back-up.
I was writing language pack with Anjel v.2.1.0 and it stopped right at the beginning. After that I can't connect to the mobile. I even put out the battery fot the night and it didn't help. I'm always trying with different softwares with no success.
Is there any back-up battery in Alcatel 311?

Thank you for your help.

Best regards,

Dusan

[cosmo]

Hi guys!!!
What cable u use,made in factory or home?U use usual 1,2with 3,4 and 5,or 1,2,3gnd, 4 and 5?

My best regards to alll!

[dusan.g]

I'm using home made cable with MAX232 with external power. My pinout is: 1,2,3 - GND, 4 - Rx, 5 - Tx. It worked with two Alcatel 511 and also with this 311 until I started to write a language pack.
I had also one dead 511 - I removed battery for the night and in the morning I was able to connect to the phone. But now with this 311 it seems to be impossible to connect to it. Please help.

Dusan

[cosmo]

Hi dusan!!!
Almost all prog from here by cable are using interface from afilip and for that just 1-gnd,2-3 shorted,4-tx,5-rx, so u can modify your cable for good comunication with pc!!!!

MY BEST REGARDS TO ALL!!!

[V.S@]

hi, my cable is home made, i use 1-grd 2,3-shorted 4-tx 5-rx, and i´ve already unlocked some 511, and some 311 too, and i even had killed one 311, with 311 unlock 1.2 by Angelo stupid program, and now the phone is alive again..All this, allways with my cable, that worcked since the first time that i make it.

[dusan.g]

What program did you use to bring your dead Alcatel 311 back to life?

Thanks.

Dusan