Cect Q380 Pinout

[e_motion_bbsr]

cect Q380

need pinout of this model

connector type 2X5

6 PIN IS GROUND

NEED RT TX

PLEASE HELP IF ANYONE HAVE

[InfinityHelp]

hello!

check this
http://forum.gsmhosting.com/vbb/showpost.php?p=2876298&postcount=386

[noi]

in my infinity its hard to detect that unit. I repaired the unit q380 . easy to flash and format, now the phone working good.

[e_motion_bbsr]

NOT CONNECTING IN THAT PINOUT

4-RX
5-TX
6-GnD

PHONE COMMING ON

[InfinityHelp]

hello!

change with places tx and rx

[e_motion_bbsr]

same
not connecting after also alternating rx,tx
also not able to read general information .
phone is in on condition restarting with sim

[e_motion_bbsr]

u have given wrong pinout sir now i am able to connect it
thanks for support


COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
chip: 0031:A3E3:B51C
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.38D7E141.[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN_290A B488].rpl
New firmware detected:
BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN

- make "Repair security area" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
device-id: 38D7E141
identification#1 protocol ver: 04
ver. sw1: BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN
ver. sw2: BR26_35.54
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.


warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
reading [flash[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN]]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_flash[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN]_20080108-133026.B0M.bin
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _38D7E141_BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_5 4.BIN_290AB488_20080108-133047.B0X.bin
Finished, time used: 370 sec
Remove/Install battery now !

[InfinityHelp]

hello!

please - send "backup_system_log" and phone full flash backup to support
also please tell us a correct pinout for this phone
thank you!!

[e_motion_bbsr]

Correct Pinout Is Inside Kepad Steaker. Left Side.soon I Will Send Flash Back Up To Support

[ryukie78]

u have given wrong pinout sir now i am able to connect it
thanks for support


COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
chip: 0031:A3E3:B51C
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.38D7E141.[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN_290A B488].rpl
New firmware detected:
BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN

- make "Repair security area" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
device-id: 38D7E141
identification#1 protocol ver: 04
ver. sw1: BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN
ver. sw2: BR26_35.54
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.


warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
reading [flash[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN]]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_flash[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_54.BIN]_20080108-133026.B0M.bin
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _38D7E141_BR26_05C_PCB01_GPRS_MT6226_S01.BR26_35_5 4.BIN_290AB488_20080108-133047.B0X.bin
Finished, time used: 370 sec
Remove/Install battery now !

tnx bro plss..plsss post your pinouts tnx

[InfinityHelp]

hello!

guys, please note that some Q380 has spreadtrum CPU.
so even with correct pinout you will fail to connect with infinity software.
So if a first place- make sure which MCU you have in phone, after that look for pinout

[joalbert_ramos]

hello,,

can you show the image of the phone pin out ,,,
thanks ,,
i have a jaf box , i only use crack software,,

[InfinitySupport]

hello,,

can you show the image of the phone pin out ,,,
thanks ,,
i have a jaf box , i only use crack software,,

Here is Infinity-Box support forum but not a discussion about crack software.
You must leave this forum now !

[Sindong]

hello!

guys, please note that some Q380 has spreadtrum CPU.
so even with correct pinout you will fail to connect with infinity software.
So if a first place- make sure which MCU you have in phone, after that look for pinout

So for Spreadtrum CPU its not supported yet? is it diff from the mt series CPU?

[InfinityHelp]

hello!

Spreadtrum CPU is different from MT62xx
it is not supported yet

[Sindong]

When can we have support for this spreadtrum CPU? i think other boxes supported it now. we may be eaten by competition if we do not do something quick. or i say its too late for now?