any one help me n95

[cnnmbc]

hi all man
can any on help me to find pinouo
for n95 china double slider music edit

138862

138863

138864

[tsarkh]

check the point marked

[cnnmbc]

thank you man
but this point is not work
help me

[cnnmbc]

:confused::confused::confused:

[InfinitySupport]

thank you man
but this point is not work
help me

Hello,

Try to swap Rx <-> Tx wires.

[cnnmbc]

Hello,

Try to swap Rx <-> Tx wires.

i make this note
but dont work
read this
if i read eeprom
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02]...
chip: 0000:0000:0000
error: initialize step#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 12 sec
Remove/Install battery now !

if i format ffs
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02]...
chip: 0000:0000:0000
error: initialize step#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 12 sec
Remove/Install battery now !
please
help me
:confused::confused::confused::confused::confused: :confused:

[InfinityHelp]

hello!

do you hold power button pressed all time while phone boots? until software asks to release it?

[cnnmbc]

hello!

do you hold power button pressed all time while phone boots? until software asks to release it?

i make it.... but do not format
:confused::confused::confused::confused:

[InfinityHelp]

hello!

i think you must look for other pinout. Some chinese phones have few data ports, but only one work for boot_operations.

[cnnmbc]

where i can find it???????????????

[tsarkh]

man i can told u that i am sure of the pinout and i do it myself

there is one more thing u can check did u see the third point near these two points???

try to put ground on it and see what happen????

and one more thing i am sure of the pinout

[cnnmbc]

man i can told u that i am sure of the pinout and i do it myself

there is one more thing u can check did u see the third point near these two points???

try to put ground on it and see what happen????

and one more thing i am sure of the pinout

thanke you for write thes not
can you write rx..tx and ground on pic

[cnnmbc]

i make this pic
139082

[cnnmbc]

please
help me
please
help me
please
help me

[InfinityHelp]

hello!

looks like cable is soldered properly.
what is phone problem? IF not power On- maybe some interneal hardware fault in power ciruit?

[cnnmbc]

if i press read general information
it give me this
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: Kongli26_06B_HW
Software version: MAUI.06B.W07.04.MP.V
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 357927005716447
Finished, time used: 51 sec
Power off phone now !

and if i press read full flash it give me this

COM6 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
chip: 0031:AC41:4CB0
high speed disabled
error: initialize step#7 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 7 sec
Remove/Install battery now !

:confused::confused::confused::confused:

i do not what is problem
heeeeeeeeeeeelp me

[GuruKids]

Please select lower speed.

[cnnmbc]

i select all speed.
115200
230400
460800
921600
slowest

[InfinityHelp]

hello!

are you using latest CM version? Do you hold power button long enought?

[cnnmbc]

1-what is latest CM version????
2-yes... i hold power

[InfinityHelp]

hello!

CM- chnese miracle software
latest version

[cnnmbc]

yes v2.23
139474
139474
:confused::confused::confused:

[InfinityHelp]

hello!

this is happening only with one single phone or with many different?

[cnnmbc]

i make it whith vepro box
by this pin out in the pic
and the phone is very goooooooooood now
???????????????
!!!!!!!!!!!!!!!!!!!!

[cnnmbc]

where is infinity help & infinity team!!!!!!!!!!!!!!!!!!!!!!

[cnnmbc]

!!!!!!!!!!!!!!!!!!!!!

[InfinityHelp]

hello cnnmbc!

sorry, i dont get idea of your question.
I thought you solved problem already