pinout of nokia 5310

[tandjatelecom]

hello

i have nokia 5310 and d'ont have pinout help please

thinks

[InfinityHelp]

hello!

is it double MCU phone? WHat is connector type and where is located GND pin?

[allal123]

NOKIA 5310_NMM-3 XPRESS MUSIC

fully supported

PS : pinouts on PCB not work , phone can connect only via connector . for more infos check attached screenshot .


NOKIA 5310_NMM-3 XPRESS MUSIC connector

keyboard up
1----------8

RX = 3
TX = 4
GND = 5


==== log opened: [04/02/2008 11:23:39] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.24
S/N: 09BC:010C
Wait...
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
chip: 0001:FC03:0006
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: SHINEC25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_16 _L5_MP4_MY_V1_1.BIN
ver. sw2: MAUI.06B.W07.16_L5_mp4_MY_V1.1, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:18E59F00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
reading [eeprom[SHINEC25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_16 _L5_MP4_MY_V1_1.BIN]]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom[SHINEC25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_16 _L5_MP4_MY_V1_1.BIN]_20080204-113708.B0E.bin
Finished, time used: 101 sec
Remove/Install battery now !

COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
chip: 0001:FC03:0006
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: SHINEC25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_16 _L5_MP4_MY_V1_1.BIN
ver. sw2: MAUI.06B.W07.16_L5_mp4_MY_V1.1, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:18E59F00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
reading [flash[SHINEC25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_16 _L5_MP4_MY_V1_1.BIN]]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_flash[SHINEC25_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_16 _L5_MP4_MY_V1_1.BIN]_20080204-114823.B0M.bin
Finished, time used: 704 sec
Remove/Install battery now !


WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

Do you want to continue ?
COM4 [VCP0] selected
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6225:8A03:8A00]...
CPU: MT6225
chip: 0001:FC03:0006
Connecting, wait...
Release Power button now !
Phone detected, wait...
warning: can't read software version, probably unknown firmware
detecting structure #2...
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18warning: wrong packet cs
19 20 21 22 23 24 25error: detection failed (26 tries), read flash and send to support
connection lost
error: operation failed !
Finished, time used: 6 sec
Remove/Install battery now !


Action: imei
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6225, E03
Hardware version: SHINEC25_06B_HW
Software version: MAUI.06B.W07.16_L5_m
Software date: 2006.06.14
Barcode: MT012345678901234567
imei: 135790246811220
imei write method: mode-1
new imei: 355502461859320
imei verified Ok
Finished, time used: 6 sec
Power off phone now !

[InfinityHelp]

hello allal123!

thank you for sharing this information!!!
we will include it in next pinout update.
are you sure regarding PCB pinout? is it marked as "tx", "rx" or just unmarked test points?

[allal123]

hello allal123!
are you sure regarding PCB pinout? is it marked as "tx", "rx" or just unmarked test points?

yes with pcb pinouts i can't connect this phone , only with external connector .

[InfinityHelp]

hello allal123 !

if you work with marked test points on PCB here is general rule:

phone TX must be connected to box RX
and otherwise phone RX must be connected to box TX

i think you connected with test points like tx+tx, rx+rx.
this is why did not work for you

[allal123]

hello allal123 !

if you work with marked test points on PCB here is general rule:

phone TX must be connected to box RX
and otherwise phone RX must be connected to box TX

i think you connected with test points like tx+tx, rx+rx.
this is why did not work for you
hello
i know tx on phone must be connected on rx box rx phone must be connected on tx box , but this model is not same to others CM PLATFORM .Or his mother board is defective :rolleyes:
ps . i have good experience for this chinese models also i can connect it from component inside phone without pcb jtag and without external connector but it's make more time to test it . ;)
in any case important is in finitybox can repair all this crap phone without prob :)