problem with new version v 2.27 chines miracle

[yacino77]

with new version v 2.27 chines miracle write :

COM4 [VCP0] selected
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6225:8A03:8A00]...
CPU: MT6225
chip: 0001:8003:0000
Connecting, wait...
Release Power button now !
Phone detected, wait...
warning: can't read software version, probably unknown firmware
detecting structure #2...
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
warning: wrong packet cs 19 20 21 22 23 24 25
error: detection failed (26 tries), read flash and send to support
connection lost
error: operation failed !
Finished, time used: 11 sec
Remove/Install battery now !
i have nokia n82i

[InfinityHelp]

hello!

please make complete format instead of safe
better make backup before this for emergency case

[yacino77]

in complete format write:

COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
chip: 0001:8003:0000
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:18E59F00000000
error: no any expected answer: wrong answer after chip cfi request
flash: EC257E25082501:18E59F00000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: E558_JQ3F8_E558_GPRS_MT6225_S00.V60_01_1.BIN
ver. sw2: E558_JQ3F8.V60.01.1, 00000000
ffs offset/size: 00E00000/001FF000
detect device identification#2...
detection phase #1...
.
warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:18E59F00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
reading [eeprom[E558_JQ3F8_E558_GPRS_MT6225_S00.V60_01_1.BIN]]...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
warning: wrong data size at 0x00E03000, retry...
error: too many retries during read operation
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
error: no any expected answer
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
error: no any expected answer
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
error: no any expected answer
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
error: no any expected answer
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
error: no any expected answer
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
error: no any expected answer
Probably errors exist during flash read operation.
Do you want to repeat read operation ?
operation canceled by user

[mansi]

is it ZTC phone?


BR
Mansi

[.:NorthStar:.]

my friend
please just use 460800 baud rate for this error

[InfinitySupport]

@yacino77
What type of cable you have used ?
There is a big chance that it's cable problem.

[yacino77]

please solution for this problem

[yacino77]

i have original cable for infinity box

[InfinitySupport]

Please, give me an answers to all my questions:

1. What was original phone condition ?
2. What is battery voltage ?
3. Did you had a chance to open phone and check it's hardware ?
4. Did you tried to repeat the same operation ?
5. if yes, what is the results ?
6. if the same error exist: is the error on the same address or on different addresses during reading ?
7. did you tried to make "format" with disabled "backup" option in "settings" page ?

[yacino77]

i test all solution
not work

[InfinityHelp]

Please, give me an answers to all my questions:

1. What was original phone condition ?
2. What is battery voltage ?
3. Did you had a chance to open phone and check it's hardware ?
4. Did you tried to repeat the same operation ?
5. if yes, what is the results ?
6. if the same error exist: is the error on the same address or on different addresses during reading ?
7. did you tried to make "format" with disabled "backup" option in "settings" page ?

[fateh76dz]

nade N82i PinOut





hlep

[InfinitySupport]

Dear Friend,

Currently many "Chinese" models with the same name but absolutely different hardware exist on market.
Exmple: exist at least 20 phones with name "Chinese Nokia-N95" but all models has difference in hardware,
different bottom connectors, different pinouts and and has different firmware,
so we recommend you to include the next information in your request regarding pinout:

1. detailed description of model: brand name, model name, complete text from phone back label, any other marks that you can find on phone cover
2. phone CPU chip name
3. phone PCB photo (Rx/Tx/Gnd test-points may exist on phone PCB)
4. attach phone photo
5. attach phone bottom connector photo
6. include information about Gnd and Charge pins on phone bottom connector

After you have this information prepared, you can find pinout by yourself more easy than before,
just check the next detailed description how to get pinout for your model:

1. use "Cable Selector": http://forum.gsmhosting.com/vbb/showthread.php?t=398297
2. if not helps, please read: C:\Program Files\InfinityBox\pinout\ChineseMiracle\
3. if not helps, please read: http://www.gsmhosting.com/vbb/showpost.php?p=2212036&postcount=7
4. if not helps, please read: http://www.gsmhosting.com/vbb/showthread.php?t=433447