problem tp auto start

[roljicz]

hi I hew old dreambox(siemens) upgrade to SE and I haw a problem with auto start tp.just like on picture I haw enable option auto start tp but when start eni function with tp auto start option is disable .
thanks

[GSM Dream]

Hello roljicz!
You can configure testpoint sensitivity in testpoint window.

[roljicz]

hi ok is what you say about test point window but in my case only START and ABORT are activate . TESTPOINT CONNECT SENSITIVITY and AUTOSTART are disable I can not do anithing with them.
TNX

[GSM Dream]

hi ok is what you say about test point window but in my case only START and ABORT are activate . TESTPOINT CONNECT SENSITIVITY and AUTOSTART are disable I can not do anithing with them.
TNX
Can you send screenshot of testpoint window?

[roljicz]

this the picture
thanks

[dimon]

roljicz, you have old dreambox, not plus version
tp autodetect will no work for you

[dimon]

dream team, please make auto start option with changeable delay after connect TP popup window for users with old boxes

[roljicz]

ok. but you will told that about old box without autostart tp!!!
another quest for you this is a log file .I can write flash,all function but can not do this.
Security Bypass------------------------------------------------------------
User selected phone K800 using Test Point boot mode
Stage 1 started
1) Turn OFF the phone.
2) Connect the phone to DreamBox cable.
Boot Responce = 5A
Processor ID = 99000301FFFFFFFF (DB2020 / DB2030)
NOR Flash ID = 2019
OTP Status = LOCKED
OTP IMEI = ******x01-644339-7
OTP CID = 49
EROM Color = 4 : RED
EROM CID = 52
Hint : Now the probe might be disconnected
Processing ...
Stage 1 completed succesfully
Stage 2 start
Hint : Now the probe might be disconnected
Processing...



where is a problem

[GSM Dream]

Hello roljicz!
1. Try to update box's formware to 1.11
2. Try to do Execute "Security Bypass" for Stage 2 again.

Old dreambox hardware can’t support some features of DreamBox Plus (autoignition, auto detect testpoint connection). This is hardware problem, so some features can work only with new hardware (DreamBox Plus or DreamBox SE)

[paullovinicius]

Hello roljicz!
1. Try to update box's formware to 1.11
2. Try to do Execute "Security Bypass" for Stage 2 again.

Old dreambox hardware can’t support some features of DreamBox Plus (autoignition, auto detect testpoint connection). This is hardware problem, so some features can work only with new hardware (DreamBox Plus or DreamBox SE)

Sir, I know that is very difficult, but is there any way to add this missing features to old DB or improve it?
Thanks

[Skaza]

and i have problem connect TP software preparing and this preparing long time 30min and user stop my softwar freez 705cps - 0 cps and this the end

[GSM Dream]

To paullovinicius
No way, unfortunately :(

To Skaza
We need more details!
1) Phone model
2) Phone firmware version
3) DBSS version
4) DBSS log files (dbss.log and dbsserr.log)
6) Exact sequence, what you were doing
Thank you.

[paullovinicius]

To paullovinicius
No way, unfortunately :(
Thank you.

Thanks, sir.
And that method to repair "Short curt detected!" that exchange a capacitor for a resistor(or vice-versa), can be used with old DB to improve some thing?

Thanks!

[GSM Dream]

To paullovinicius
Check your pm.

[Skaza]

1) Phone model K800i
2) Phone firmware version ,i dont know (problem z customize)
3) DBSS version 3.0
4) DBSS log files ok sent pm
i need repair gdfs