paedy
02-28-2008, 08:15
I have Beyond B610...
Need Format but can not connect
Use Infinity finder L12c cable.
if i use power from pinfinder, phone can not power on. use bat or power supply phone can power on.
But if i select Via additional harware line here's a log i f i press find it :
software version: 1.06
cable type: 1x12 (L12C)
platform: MT62xx (autodetect)
searching adapter at COM6...
adapter found, version: 2000
pins: 12, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
too many retries
connection w/adapter lost during set Tx as pin 3
failed to detect pins
time required: 1 sec
too many retries
Power Off !
If use power from pinfinder can not find rx and tx.
I use Usb cable from phone... Phone can read general information and here's log :
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: FYD26_05C_HW
Software version: V826_ind_V09"
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 353399061031042
Finished, time used: 4 sec
Power off phone now !
Then I try one by one to change rx tx with finder and find some respon if i select Rx 1 and tx 6 but cannot conect to phone.
And here's log :
COM6 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: read eeprom
Boot...
Press and HOLD Power button now !
19200
Connecting, wait...
error: can't detect CPU id
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 5 sec
Remove/Install battery now !
Plz Need some Advice..
BR
Paedy
Need Format but can not connect
Use Infinity finder L12c cable.
if i use power from pinfinder, phone can not power on. use bat or power supply phone can power on.
But if i select Via additional harware line here's a log i f i press find it :
software version: 1.06
cable type: 1x12 (L12C)
platform: MT62xx (autodetect)
searching adapter at COM6...
adapter found, version: 2000
pins: 12, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
too many retries
connection w/adapter lost during set Tx as pin 3
failed to detect pins
time required: 1 sec
too many retries
Power Off !
If use power from pinfinder can not find rx and tx.
I use Usb cable from phone... Phone can read general information and here's log :
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: FYD26_05C_HW
Software version: V826_ind_V09"
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 353399061031042
Finished, time used: 4 sec
Power off phone now !
Then I try one by one to change rx tx with finder and find some respon if i select Rx 1 and tx 6 but cannot conect to phone.
And here's log :
COM6 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: read eeprom
Boot...
Press and HOLD Power button now !
19200
Connecting, wait...
error: can't detect CPU id
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 5 sec
Remove/Install battery now !
Plz Need some Advice..
BR
Paedy