Ztc 8380 Not Flash _why?

[..::topnet_gsm:]

MASTER SUPPORT SEE THIS LOG:

Device: Autodetect 6228 NAND
Checking data, wait...
Action: write NAND flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page+spare
converting data...
done 0x01F08000 bytes
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_AB_01_1_0 T01S0827.BIN
ver. sw2: R2000_AB_01_1.0T01S0827, A6A5714C
ffs offset/size: 02000000/06000000
id-page1 Ok
warning: size adjusted by end mark [+00040000], probably incorrect/damaged data
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00080000 bytes
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_AB_01_1_0 T01S0827.BIN
ver. sw2: R2000_AB_01_1.0T01S0827, A6A5714C
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_AB_01_1_0 T01S0827.BIN_B38E5A59].rpl
identification#1 detection finished
security area#1 calculation...
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _AB_01_1_0T01S0827.BIN_B38E5A59_20080228-071822.B4X.bin
write core area 1 of 2...
write core area 2 of 2...
error: code: A500000BF4
error: code: 5A
error: code: A5
error: code:
error: block/offset: 00000CEE/00CEE000
error: can't write nand core
Write Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _AB_01_1_0T01S0827.BIN_B38E5A59_20080228-072339.B4X.bin
Finished, time used: 374 sec
Remove/Install battery now !


NOT FLASHED PHONE
THIS PHONE IS DEAD.
WHY?
HOW TO DO?

BR
TOPNET_GSM

[..::topnet_gsm:]

TESTED BY THIS FLASH FILE AND REPAIRED PHONE

_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_AB_01_1_ 0T01S0827__ZTC-ZT8380_128m_En_Fr_Ar.B4M.bin

THANX TO MASTER SUPPORT

BR,
TOPNET_GSM

[gsmsikar]

TESTED BY THIS FLASH FILE AND REPAIRED PHONE

_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_AB_01_1_ 0T01S0827__ZTC-ZT8380_128m_En_Fr_Ar.B4M.bin

THANX TO MASTER SUPPORT

BR,
TOPNET_GSM
how did u repaired this phone please give some details here ..

i also have a same set and i am sure it is software problem ..

please help ..

[gsmsikar]

i tried to flash this set but i am getting this error ... now what to do ?




COM8 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: write NAND flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_ML_01_1_0 T02S0824.BIN
ver. sw2: R2000_ML_01_1.0T02S0824, 218CC78A
ffs offset/size: 02000000/06000000
id-page1 Ok
warning: size adjusted by end mark [+00060000], probably incorrect/damaged data
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:4A01
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00080000 bytes
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN
ver. sw2: R2000_01_1.6T0HS0822, 3A29821D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN_E27DD6C5].rpl
New firmware detected:
RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN

- make "Read full flash" operation
- send "backup_system_log_..." file to support: mt62xx@gmail.com
- send flash backup file(s) to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
security area#1 calculation...
Initialize bootcode Done
Check firmware integrity...
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _01_1_6T0HS0822.BIN_E27DD6C5_20080410-013210.B4X.bin
write core area 1 of 2...
write core area 2 of 2...
error: code: A500000BF4
error: code: 5A
error: code: A5
error: code: 00
error: code:
error: block/offset: 00000C98/00C98000
error: can't write nand core
Backup required data Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _01_1_6T0HS0822.BIN_E27DD6C5_20080410-014058.B4X.bin
Finished, time used: 591 sec
Remove/Install battery now !

[InfinitySupport]

Hello,

Try to use another flash file from support area.

Also please, see software message and send at least backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _01_1_6T0HS0822.BIN_E27DD6C5_20080410-013210.B4X.bin file to mt62xx@gmail.com

[gsmsikar]

i again flashed my set with the backup of full flash reded before flashing ..

then it again came in same state ..

now i am getting one problem which is , i am unable to do format FFS in the phone ..
it is not ON but format FFS can be done or not ?

when i do format FFS it connect the phone but gives this error ..

COM8 [VCP0] selected
Action: reset settings
Model: Autodetect 6228 NAND
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:4A01
Connecting, wait...
error: can't finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 118 sec
Remove/Install battery now !



one more symptom i get to see in the phone is , the phone is dead but when i connect the positive & negative terminals of the pinfinder to the battery terminal of the phone and then press power ON , then in the phone display white light glows ...
can this be helpful to u .. ?





please help me sir as now i dont have much time or else i have to return the set ..

thanks

[InfinityHelp]

hello!

try to make format FFS in complete mode

[gsmsikar]

hello!

try to make format FFS in complete mode
this is what i get when i did complete Format FFS...

now what to do ?


COM8 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: NAND reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:4A01
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00080000 bytes
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN
ver. sw2: R2000_01_1.6T0HS0822, 3A29821D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN_E27DD6C5].rpl
New firmware detected:
RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN

- make "Read full flash" operation
- send "backup_system_log_..." file to support: mt62xx@gmail.com
- send flash backup file(s) to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
Initialize bootcode Done
Check firmware integrity...
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
formatting...
........................error: code: 6E00006900
Backup required data Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _01_1_6T0HS0822.BIN_E27DD6C5_20080411-102508.B4X.bin
Finished, time used: 113 sec
Remove/Install battery now !

[galaxyosama]

try format ffs and repier sec are than flash its work 100x100

[gsmsikar]

hello!

try to make format FFS in complete mode
any hint u got from my last post ?

what to do ?

[InfinitySupport]

this is what i get when i did complete Format FFS...

now what to do ?


COM8 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: NAND reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:4A01
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00080000 bytes
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN
ver. sw2: R2000_01_1.6T0HS0822, 3A29821D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN_E27DD6C5].rpl
New firmware detected:
RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN

- make "Read full flash" operation
- send "backup_system_log_..." file to support: mt62xx@gmail.com (mt62xx@gmail.com)
- send flash backup file(s) to support: mt62xx@gmail.com (mt62xx@gmail.com)
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
Initialize bootcode Done
Check firmware integrity...
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
formatting...
........................error: code: 6E00006900
Backup required data Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _27EADFDB_RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000 _01_1_6T0HS0822.BIN_E27DD6C5_20080411-102508.B4X.bin
Finished, time used: 113 sec
Remove/Install battery now !

What to do:
1. Please, follow by instruction given by software
2. Repeat format in "complete" mode again
3. Explain this phone history ! You must explain what was initial phone state, what you have tried to do etc. so detailed as possible !
We are unable to give an advices if we don't know what is the problem with phone !

@All
Please, read, remember and follow my advice marked in red color !!!
If you want to get help you must read and follow my advice !

[gsmsikar]

thanks infinity for the help provider ..

i am able to repair the set ...
after flashing with all the flash files available, matching with the firmware of the phone ..
one of the flash file worked and the set is ON ..

thanks
very much Infinity..

[sarasa]

thanks infinity for the help provider ..

i am able to repair the set ...
after flashing with all the flash files available, matching with the firmware of the phone ..
one of the flash file worked and the set is ON ..

thanks
very much Infinity..
Bro, which flash file u use . i have also a set (slider MTK6228) I tried different files but all those give error. COM14 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: write NAND flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw1: RATECH28_06A_PCB04_GPRS_MT6228_S02.R2000_01_1_6T0H S0822.BIN
ver. sw2: R2000_01_1.6T0HS0822, 3A29821D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00000000
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Fail
Finished, time used: 91 sec
Remove/Install battery now !
:confused::confused:

[gsmsikar]

u can try the files available on the infinity download area ...

i also use one flash file from the download area ... and it is working fine ...