Auto PinFinder Power Problem

[dannyogolo]

This box seems ok to me, but as with all boxes, there are a few phones that it doesnt work ok.
There are a few China phones that it cannot power. That is to say these phones comes up with battery, but not with pinfinder power cables.
Its not a matter of connecting the cables correctly, the cables are always well connected (the batteries have the "+" and "-" indicators and its almost impossible to mistake them. Also the indicator red light behind the pin finder remains on while i try to power phone (showing that the polarity is correct).

Maybe support should look at making it work with phone battery as well, or is there a way out ?

[InfinitySupport]

Please, download latest PinFinder manual: http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf
Please, see page 18: Automatic pinout detection: Troubleshooting
I hope you can solve at least 99% of possible problems (especially with 8, 12, 14, 15 pins cables) with this instruction.

One more link: http://www.gsmhosting.net/vbb/showthread.php?t=512662

[targettelecom]

this finder dont need to power on mobile ,its enugh give power for cpu and power ic to be can serach pinout .only when you make serach by finder need to stay press power key mobile untill find him.
if not find that mobile so your mobile maybe not mtk .

[InfinityHelp]

hello!

some uniboxes have very small output voltage on pin1.
Also 0,7 volts is dropping on transistor which swith power to phone.
so at the end we get voltages below 3,7 volts which is not enough to power On phone
if you have on pinfinder output voltage below 3,7v- please modify your unibox
there must be diode removed and set shortcut.
Where is located this diode you can find in pin finder user manual in troubleshooting section

[navin71]

Please, download latest PinFinder manual: http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf
Please, see page 18: Automatic pinout detection: Troubleshooting
I hope you can solve at least 99% of possible problems (especially with 8, 12, 14, 15 pins cables) with this instruction.

One more link: http://www.gsmhosting.net/vbb/showthread.php?t=512662

sir i just buy an infinity auto pin finder box can u please guide me how to use this (is there any installation cd come with this box) i have infinity box too
thanks

[InfinitySupport]

sir i just buy an infinity auto pin finder box can u please guide me how to use this (is there any installation cd come with this box) i have infinity box too
thanks

Hello,

Information is here: http://www.infinity-box.biz/index.php?id=pinfinder&lg=en

Read manual and pictures here: http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf

See video here: http://www.infinity-box.biz/download/public/Infinity-Box-PinFinder_video.rar

[navin71]

sir i have connected auto pinfinder to the pc with infinity box but while connecting it shows error like this
dongle is not activated for current software module
curent dongle activation lavel 0001
required dongle activation lavel 0011
download lattest dongle manager from support area
but when connecting through dongle manager it shows like this:-
----------Process started:10:17:20 PM----------
Locating Emeralda server...
Emeralda server#1 address found.
Connecting to Emeralda server#1...
Server connection successfully established.
S/N: *********Firmware: *****
Authenticating on server...
Authentication successfull.
Checking upgrade client version...
Your upgrade client is up-to-date.
Checking Dongle Identification...
Dongle Identification checked.
Activating module...
Module check error: Server reported error:[0044] Module S/N is already registered. Don't try more !

[InfinityHelp]

hello!

need same log file but with full dongle detales to mailbox: infinityremoteupdate@yahoo.co.uk

[mansi]

@dannyogolo
maybe your phone is not MTK based, maybe its spreadtrum or something else. [which you cant auto detect pinouts] with standard cables come with pinout finder.
one small advice: open phone and check CPU type [info is writen on cpu] if its MTK or not.
BR
Mansi

[navin71]

hello!

need same log file but with full dongle detales to mailbox: infinityremoteupdate@yahoo.co.uk

Thanksssssssssssssssssssssssssssssssssssssssss PIN FINDER IS ACTIVATED
THE GREAT SUPPORT I EVER SEEN
THANKS AGAIN INFINITY TEAM
q.:- can rx tx can be find out from dead set ?
q;- is it necessary to connect +ve and -tve wire (mean can we used battery instead of wire)

[gsmxpert]

to me, pinout finder usage is not traumatic..................

[InfinityHelp]

hello mr. navin71!

please read user manual, there is all questins answered:
http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf

[Faisal_Computer]

One Qua.

when i try to connect mobile with BOX power its works fine with 80% mobiles and when i insert bettery or try to use Power Supply ( not from Box ) its gave this

software version: 1.06
cable type: 1x8 (L8A)
platform: MT6205, MT6217-MT6228
searching adapter at COM7...
adapter found, version: 2000
pins: 8, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
error: boot initialization step-2 failed: A0
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
19200
failed to detect pins
time required: 28 sec
Power Off !

so is this mean that we must use power from box ?

and also some mobile can't power up even pinout finder find pins for example 2 or 3 days ago i got Lg Kg200 pinout finder detect pins ( power from BOX ) and i need to rebuild IMEI on power from box its can flash but when i try to rebuild imei mobile not powering up can you advice me how to solve this type of problems , on the box +tv i got 5 volts and works fine just i got these type of problems

Br

Faisal_Computer

[asad_nomy7]

bro faisal i think the power cable from the box work as GND pin also.and when we connect it other power source its not have GND pin then not detect RX/TX.

[milankumardoshi]

sir output#2 of pinfider has rj45 but the power terminal was given with 10 pin jack with 10 wires inside does it cause some problem.i get output 5 v

[InfinityHelp]

hello!

yes, power lines is also used to connect GND.
To deliver more power to adapter you can modify your unibox by removing usless diode.
we have this method described in our user manual on page 20

[Faisal_Computer]

bro faisal i think the power cable from the box work as GND pin also.and when we connect it other power source its not have GND pin then not detect RX/TX.

yes may be you are right but two pins on pinout#1 one of two is GND

may be Infinity Helps Us
Br

Faisal_Computer

[Faisal_Computer]

hello!

yes, power lines is also used to connect GND.
To deliver more power to adapter you can modify your unibox by removing usless diode.
we have this method described in our user manual on page 20

yes Brother i have readed but can you tell me if i want to use External Supply so is it possible that i can use GND from rj45 and +tv from External Supply ?

Br

Faisal_computer

[InfinityHelp]

hello!

if you wish to add external power to box i think best way is modify cable between boxes.

[Faisal_Computer]

Thanks for info

Br

Faisal_Computer

[dannyogolo]

I did modification as in NEW manual, and so far I have powered phones that refused to power (3 pcs with me).
As Faisal said, this applies to about 20% of the total phones tried

[navin71]

[sir i have downloaded new version on pin finder and installed properly but why this version failed to detect pin (rx and tx ) is there any other setting to do with this version ?

[InfinitySupport]

Please, explain what is the problem so detailed as possible so we will be able to understand the problem.

[dog_baby]

Mr InfinitySupport
I have bought infinity box +pinfinder box and have installed them .Pinfinder have deteced but when scan pinout with MT62xx chip show '' failed to detect pins''.I tried with a lot of MT chip but still Fail.
Please help me.THANKS

[InfinityHelp]

hello mr. dog_baby!

you might be doing some mistake while searching.
i would advice to read one more time pinfinder user manual
if still have problems- reffer to trubleshooting chapter.
might be needed diode removing or capacitor instalation