Huawei T201 Not Detect In Ver 1.41

[chiragp]

Tried With C2500 Cable Manuall Made Rx Tx

Also Solder Direct On Pcb Rx Tx

But No Responce

Says Power And Hold Button

Need To Unlock

Waiting

Thanks

[InfinitySupport]

Hello,

To be honest I have no any good idea, only think that something wrong with cable.
Please, try to swap Rx <-> Tx wires.

[jamil fernandez]

Negative I cannot read Huawei T-201, Or badly the pinout of the LG-C2500 Or this not compatible?

[jamil fernandez]

Support answers please need unlock phone T-201 please

[InfinitySupport]

Hello,

Please, use LG C2500 cable and unlock T201 with Infinity-Box.
If phone can't be detected by software double check your cable and check that phone connector is clean and is not damaged.

[josh_aina]

Hello,

Please, use LG C2500 cable and unlock T201 with Infinity-Box.
If phone can't be detected by software double check your cable and check that phone connector is clean and is not damaged.
Hello Infinity Support!
It's the best and true pinout but it doesn't work with the old model of t201
It has 2 models of huawei t201. Infinity work with the new model correctly. It is the difference: the resistor 220ohm connect to the pin4 (rx) at the new phone is not same at the old (4.7 kohm)
Best regards

[josh_aina]

hi!
I try to replace the resistor but it doesn't work still!

[InfinitySupport]

Hello,

Could you, please, make a photo and send it to InfinityBoxSupport@gmail.com

Is it was any luck with connection after you have replaced that resistor ?

[josh_aina]

Hello,

Please, use LG C2500 cable and unlock T201 with Infinity-Box.
If phone can't be detected by software double check your cable and check that phone connector is clean and is not damaged.
Hello Infinity Support!
It's the best and true pinout but it doesn't work with the old model of t201
It has 2 models of huawei t201. Infinity work with the new model correctly. It is the difference: the resistor 220ohm connect to the pin4 (rx) at the new phone is not same at the old (4.7 kohm)
Best regards

[josh_aina]

Hello,

Could you, please, make a photo and send it to InfinityBoxSupport@gmail.com

Is it was any luck with connection after you have replaced that resistor ?
It not connect still! What do I do? I send picture later because I haven't camera here!

[InfinitySupport]

Are you sure that phone that you have is Huawei-T201 ?

[akhil_bbsr]

use 10 k R ...all ok......

[johnreza]

it's correct there is two types of this T201 Huawei . one connect well and unlock without pb but 2nd dont respond on boot at all ...

@ josh_aina

For info : T201 with grey statup logo connect well and T201 with green logo don't connect :D

[InfinitySupport]

it's correct there is two types of this T201 Huawei . one connect well and unlock without pb but 2nd dont respond on boot at all ...

@ josh_aina

For info : T201 with grey statup logo connect well and T201 with green logo don't connect :D

What is CPU chip name in T201 with green logo ?
It's very strange that the same model has so different properties.

[johnreza]

Will check and reply tomorow sir ...

Thanks
Regards

[arabe]

Please put the image of the modification cable huawei t201

[wahid_2]

:)Hi team

I can not unlock Huawei T201 ??

log :

COM5 [VCP0] selected
Device: Huawei-T201
Checking data, wait...
Action: unlock
unlock method-1
Boot...
Press and HOLD Power button now (if boot does not start remove/install batery) !
loading...
next part...
error: can't run main loader:
Release Power button now
Boot Failed
Finished, Remove/Install battery now !
Time used: 7 sec

[InfinitySupport]

@wahid_2
This problem was described several times already, this phone has 2 different PCB types (as we was informed by some users).
We are waiting for high-quality photos of both PCB modifications to find the solution: InfinityBoxSupport@gmail.com

[nexxus63]

unlcok huawei is supported our not

[InfinitySupport]

unlcok huawei is supported our not

Hello,

As I remember you can see two types of T201 in software.
If phone can not be unlocked like "T201 HW-A" just select "T201 HW-B" and repeat unlock operation.