strang problem not with all chinese

[pinkfloyd2]

some kind of chinese mobile phone can boot just if i press and hold the power bottom and if i press the power bottom untill the phone is booting then leave it the booting stop and should repeat the operation from the begining with press and hold the power bottom then i cant format it or make any operation even i press and hold power bottom just phone booting then error..

any idea for this strang problem

[InfinitySupport]

Hello,
To be honest it's quite hard to understand so so many words followed one by one without any dot or comma.

Easy rules:
1. if software say "Press and HOLD..." it's good idea to press and HOLD phone button
2. if sofwate say "Release button" it's good idea to release buton

[pinkfloyd2]

i know what you said i`m not new in this work

try to understand me

when softwear say release buton i do then phone stop booting i have to hold and press powe booton all the time to get phone pooting

[mansi]

do u get this problem with all chinese phones?
because i got this problem with one phone b4 and the problem was hardware [flash chip] i reheated it and the phone booted correctly after that.

hope i have ben helpfule.
P.S: sometimes setting lower baudrate is good idea.
BR
Mansi

[pinkfloyd2]

Not With All Just With aLL MT6205

[charletan]

Not With All Just With aLL MT6205

hello pinkfloyed pm me i have the solution for chinese mobile not detected or
error in read its not software it hardware of box

[charletan]

hi pro now u see the error
COM3 selected
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
error: boot phase#2/1 failed
Can't initialize test mode !
Possible reasons:
1. communication fault, repeat required operation
2. eeprom/ffs serious damaged, use repair eeprom/ffs files or use other unlock/format method
error: operation failed !
Finished, time used: 4 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

[charletan]

now u see the probleme solved



Wait...
Device: Autodetect 6205-6227 NOR
Done
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: Nokia N73(11)
Software version: V2.0628.0.0.1"
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 353641015975117
Finished, time used: 53 sec
Power off phone now !
COM1 selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:94C1:CBCA
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.81F69322.[FS26_05C_SET_PCB01_GPRS_MT6226_S01.V2_0628_0_0_1.B IN_AEFFB3F9].rpl
identification#1 detection finished
device-id: 81F69322
identification#1 protocol ver: 04
ver. sw1: FS26_05C_SET_PCB01_GPRS_MT6226_S01.V2_0628_0_0_1.B IN
ver. sw2: V2.0628.0.0.1, 064C0051
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
detecting ffs structure pass 1...
...................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.................................................. .....
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
detecting ffs structure pass 2...
...................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.................................................. .....
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #2 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _81F69322_FS26_05C_SET_PCB01_GPRS_MT6226_S01.V2_06 28_0_0_1.BIN_AEFFB3F9_20080401-161540.B0X.bin
Finished, time used: 91 sec
Remove/Install battery now !
COM1 selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:94C1:CBCA

[InfinityHelp]

hello!

6205 is second MCU. (MCU_b)
it has specific booting sequence.

for example: you connected infinity box to second MCU pinout (tx_b, rx_b)
so now, to get communication with it you must press power button and wait arround 1 minute (holding all time power button).
this is because in a first place in this phone will start First MCU (MCU_a)
after it started- you will see message "insert sim". Dont worry, still keep power button pressed.
after some time program will detect second MCU and will start load boot file to phone.
only after program will say "release button" you can release it.

this procedure can be much more simple if you use "power_b" test point.
by setting it to GND you make CPU2 boot imidiatly
no even need to press power

i hope i answered your question about little strange boot sequence of second MCU.
if not- ask more detailed

[tarunvishal]

this fault is come from cpu and flash ic rehot both ic and try ur set boot in one press