K99 Nktel Flash File

[masudtel]

k99 Nktel Flash File
my6226_pcb01_gprs_mt6226_s01.dm200_v009_1_3_win.bi n

[InfinityHelp]

hello!

dont have exactly same flash file on support, but worth to try after full backup following file:
flashfiles/ChineseMiracle/_MT6205-MT6227/CM_Nokia-N66-2sim_MY6226_PCB01_GPRS_MT6226_S01.DM200_V009_1_3_M ATRIX_16m_En_Ru_Vn_Th.B0M.bin
also one question: did you try format FFS to solve your problem? I am asking because flashing is a last thing to do with faulty chinese phone

[masudtel]

ist time this phone given restart 1st time i'm using super doctor box to doing format then format ok phone was dead then use infinity notpower on.....all work coplete of infinity but not power on.................

[InfinityHelp]

hello!

i still insist on flashing by adviced above flash file.
as long as your phone already dead- no point to make backup because you can not use it to repair your phpne anyway

[masudtel]

COM10 [VCP1] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:9DC1:BF5E
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 89880F00010001:89880F00000000
flash: Intel Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 89880F00010001:89880F00000000
flash: Intel Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 89880F00010001:89880F00000000
flash: Intel Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 89880F00010001:89880F00000000
flash: Intel Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.C9FE0312.[MIKI26_05C_PCB01_GPRS_MT6226_S01.V20_56.BIN_C37511 97].rpl
identification#1 detection finished
device-id: C9FE0312
identification#1 protocol ver: 04
ver. sw1: MIKI26_05C_PCB01_GPRS_MT6226_S01.V20_56.BIN
ver. sw2: V20.56, 68EE8A3C
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 89880F00010001:89880F00000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
flash: 89880F00010001:89880F00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: 89880F00010001:89880F00000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _C9FE0312_MIKI26_05C_PCB01_GPRS_MT6226_S01.V20_56. BIN_C3751197_20080331-112407.B0X.bin
Finished, time used: 155 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

[masudtel]

all information of my phone...........

[InfinityHelp]

hello!

what is this log?
why there is MIKI26_05C_PCB01_GPRS_MT6226_S01.V20_56 software version in phone?
which version is original? mentioned above or:
my6226_pcb01_gprs_mt6226_s01.dm200_v009_1_3_win