Chandreshswami
04-13-2008, 07:08
I have recieved Tecno St880/V90i
with problem of restarting with sim inserted
i had formmatt with infinity chinese miracle v2.37
after formatt phone is dead
here is log
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:6CAC:E3A7
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.4221152D.[E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN_D6B615EE].rpl
identification#1 detection finished
device-id: 4221152D
identification#1 protocol ver: 04
ver. sw1: E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN
ver. sw2: E553_K10F8.00.0, 11EA4929
ffs offset/size: 00800000/001FF000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00800000
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00800000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
operation terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
flash: EC257E25082501:29EA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: EC257E25082501:29EA0000000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _4221152D_E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN _D6B615EE_20080412-123136.B0X.bin
Finished, time used: 134 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !
phone cant power on ( pressed long for 2 min )
as per log its says File system has modified
Phone is Dead
NOW I HAVE DOWNLOADED EPPROM AND FIRMWARE FROM SUPPORT
E553_K10F8_E553_GPRS_MT6226_S01.00_0_ffs_01.B0E
E553_K10F8_E553_GPRS_MT6226_S01.00_0_16m_En_Ru_Fr_ Es_De_Th_Vn_Tr_Ar.B0M
And try to flash but cant succed here is log
==== log opened: [4/13/2008 10:01:49 AM] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.37
S/N: 04F9:010E
Wait...
Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
E553_K10F8_E553_GPRS_MT6226_S01.00_0_ffs_01.B0E.bi n loaded
detecting languages...
Languages: not detected
Loading file v.02...
E553_K10F8_E553_GPRS_MT6226_S01.00_0_16m_En_Ru_Fr_ Es_De_Th_Vn_Tr_Ar.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw1: E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN
ver. sw2: E553_K10F8.00.0, 11EA4929
You have loaded file with security features enabled.
detecting languages...
Languages: En Ru Fr Es De Th Vn Tr Ar
Loading file v.02...
E553_K10F8_E553_GPRS_MT6226_S01.00_0_ffs_01.B0E.bi n loaded
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
error: can't detect CPU id
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 11 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 14 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 21 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:6CAC:E3A7
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com (mt62xx@gmail.com)) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom_200 80413-101132.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
Area: Firmware
flash: EC257E25082501:FFFFFF00000000
Write: Firmware
error: error# 000000FF
error: flash write error: 00000000:00002000
error: no any expected answer
error: flash write error: 00000000:00002000
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 462 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:6CAC:E3A7
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com (mt62xx@gmail.com)) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom_200 80413-101958.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
Area: Firmware
flash: EC257E25082501:FFFFFF00000000
Write: Firmware
error: error# 000000FF
error: flash write error: 00000000:00002000
2E3B3B3BFC2E3B3B3BFC2E3B3B3B332E3B3B3BE72E3B3B3BFC 2E3B3B3BFC2E3B3B3B2C2E3B3B3B502E3B3B3B482E3B3B3B7A 2E3B3B3B1C1A2E3B3B3B7A2E3B3B3BE42E3B3B3BFA1A1A8BC8 EC6658
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 427 sec
Remove/Install battery now !
PLEASE HELP ME
WHAT TO DO?
THIS IS 1st PHONE ANOTHER PHONE 'S DISPLAY IS BLANK AFTER FORMATT
BOTH R SAME PHONE SAME FIRMWARE
with problem of restarting with sim inserted
i had formmatt with infinity chinese miracle v2.37
after formatt phone is dead
here is log
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:6CAC:E3A7
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.4221152D.[E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN_D6B615EE].rpl
identification#1 detection finished
device-id: 4221152D
identification#1 protocol ver: 04
ver. sw1: E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN
ver. sw2: E553_K10F8.00.0, 11EA4929
ffs offset/size: 00800000/001FF000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00800000
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00800000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
operation terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
flash: EC257E25082501:29EA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: EC257E25082501:29EA0000000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _4221152D_E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN _D6B615EE_20080412-123136.B0X.bin
Finished, time used: 134 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !
phone cant power on ( pressed long for 2 min )
as per log its says File system has modified
Phone is Dead
NOW I HAVE DOWNLOADED EPPROM AND FIRMWARE FROM SUPPORT
E553_K10F8_E553_GPRS_MT6226_S01.00_0_ffs_01.B0E
E553_K10F8_E553_GPRS_MT6226_S01.00_0_16m_En_Ru_Fr_ Es_De_Th_Vn_Tr_Ar.B0M
And try to flash but cant succed here is log
==== log opened: [4/13/2008 10:01:49 AM] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.37
S/N: 04F9:010E
Wait...
Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
E553_K10F8_E553_GPRS_MT6226_S01.00_0_ffs_01.B0E.bi n loaded
detecting languages...
Languages: not detected
Loading file v.02...
E553_K10F8_E553_GPRS_MT6226_S01.00_0_16m_En_Ru_Fr_ Es_De_Th_Vn_Tr_Ar.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw1: E553_K10F8_E553_GPRS_MT6226_S01.00_0.BIN
ver. sw2: E553_K10F8.00.0, 11EA4929
You have loaded file with security features enabled.
detecting languages...
Languages: En Ru Fr Es De Th Vn Tr Ar
Loading file v.02...
E553_K10F8_E553_GPRS_MT6226_S01.00_0_ffs_01.B0E.bi n loaded
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
error: can't detect CPU id
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 11 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 14 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 21 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:6CAC:E3A7
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com (mt62xx@gmail.com)) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom_200 80413-101132.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
Area: Firmware
flash: EC257E25082501:FFFFFF00000000
Write: Firmware
error: error# 000000FF
error: flash write error: 00000000:00002000
error: no any expected answer
error: flash write error: 00000000:00002000
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 462 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:6CAC:E3A7
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com (mt62xx@gmail.com)) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_***x_***x.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom_200 80413-101958.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
Area: Firmware
flash: EC257E25082501:FFFFFF00000000
Write: Firmware
error: error# 000000FF
error: flash write error: 00000000:00002000
2E3B3B3BFC2E3B3B3BFC2E3B3B3B332E3B3B3BE72E3B3B3BFC 2E3B3B3BFC2E3B3B3B2C2E3B3B3B502E3B3B3B482E3B3B3B7A 2E3B3B3B1C1A2E3B3B3B7A2E3B3B3BE42E3B3B3BFA1A1A8BC8 EC6658
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 427 sec
Remove/Install battery now !
PLEASE HELP ME
WHAT TO DO?
THIS IS 1st PHONE ANOTHER PHONE 'S DISPLAY IS BLANK AFTER FORMATT
BOTH R SAME PHONE SAME FIRMWARE