Can I reapier This Phone [Archive]

View Full Version : Can I reapier This Phone

..::AppleLinks::..

05-03-2008, 16:42

@INFINiTY SUPPORT
i always fail while doing 6228NOR....
it is power on phone,while pLaying with or doing something in it it reset,some time LCD Balck...any idea to solv ethe problem,full formate is already done.

COM3 [Serial3] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
reading structure area...
error: unexpected answer:
detecting structure...
source data: page+spare
converting data...
done 0x00080000 bytes
identification#1 protocol ver: 04
ver. sw1: BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_6680_V1_6.BI N
ver. sw2: R888_6680_V1.6, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Finished, time used: 56 sec
Remove/Install battery now !

COM3 [Serial3] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: NAND reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
reading structure area...
error: unexpected answer:
detecting structure...
source data: page+spare
converting data...
done 0x00080000 bytes
identification#1 protocol ver: 04
ver. sw1: BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_6680_V1_6.BI N
ver. sw2: R888_6680_V1.6, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Initialize bootcode Done
Check firmware integrity...
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
formatting...
.................................................. .................................................. Backup required data Done
Patch required data...
Patch required data Fail
Finished, time used: 70 sec
Remove/Install battery now !

InfinityHelp

05-04-2008, 00:06

hello!

solution for 6228 is same as for older MCUs:
start from Format (safe & complete)
continue with flashing

do not forget to make full backup before flashing

..::AppleLinks::..

05-05-2008, 07:03

hello!

solution for 6228 is same as for older MCUs:
start from Format (safe & complete)
continue with flashing

do not forget to make full backup before flashing

ya id id all tries accept complete flashing,ok tell me frm my log which version of flash files are good for me,is it in support section???

InfinityHelp

05-05-2008, 10:58

hello!

your phone software version is "BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_6680_V1_6"

..::AppleLinks::..

05-05-2008, 13:37

hello!

your phone software version is "BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_6680_V1_6"

ya i know this,support have these version ,which is best for me......thanks

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1__I808_128m_En_Cn.B4M.bin

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_432_6680_INF _HY64_V2_2_TR__ZT8900_64m_En_Cn_Cn.B4M.bin

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_432_6680_INF _HY128_V2_1__ZTC-ZT8900_En_Cn.B4M.bin

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_432_7670_HYN _HY128_V2_1__Cect-N528_128m_En_Cn.B4M.bin

InfinityHelp

05-05-2008, 22:30

hello!

there is no exact same version in mentioned above firmwares.
you can try all of them starting from end

..::AppleLinks::..

05-06-2008, 10:33

hello!

there is no exact same version in mentioned above firmwares.
you can try all of them starting from end

it is very hard to find the exact version not only in infinity support but every where....
we need some info about the versions.....
old version can cause the phone to dead??? if yes then do something for this thing also, i mean some downgrade option.
@infinity Support
you are Good Programmer...plz avoid us frm downlaoding different firmware for same cpu,make your own firmwaer,for same cpu.or try make it very easy for us,to find the exact firmware.
Thanks
BR
admin
apple team

InfinityHelp

05-06-2008, 11:05

..::AppleLinks::..

05-06-2008, 15:40

hello!

guys, we cant write firmwares for phone.
We can only upload those files which you send us.
Quantity and quality of available on support flash files- in your own hands.
just dont ignore message "new firmware detected"
spend 5 minutes to read out full flash, and 5 minutes to send it to mt62xx@gmail.com
in few days this version will appear on support

ya i know it very well,just imagine..........
look if u sart your own firmwaer it will be good and br very easy for users,
for some users it is very hard to send u the files bcz all users have no good conection,and also all chinese phones firmwaer are bigger frm 10 mb,so think that 10mb file is not so easy to upload to any server.......u also have no service for this.
and u should to start your own uploading service,also break uplod ption is also required........
thanks

..::AppleLinks::..

05-06-2008, 15:50

ya i know this,support have these version ,which is best for me......thanks

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1__I808_128m_En_Cn.B4M.bin

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_432_6680_INF _HY64_V2_2_TR__ZT8900_64m_En_Cn_Cn.B4M.bin

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_432_6680_INF _HY128_V2_1__ZTC-ZT8900_En_Cn.B4M.bin

BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_432_7670_HYN _HY128_V2_1__Cect-N528_128m_En_Cn.B4M.bin

@Infinity Support
These Files are useless for me,phone dead after flashing with these Files.

InfinityHelp

05-06-2008, 19:11

hello!

in this case the only possible way is to get working backup of exactly same firmware
BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_6680_V1_6

..::AppleLinks::..

05-07-2008, 10:37

hello!

in this case the only possible way is to get working backup of exactly same firmware
BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_6680_V1_6

i have a full bakup but it also useless for me,phone also no power on with flash bak files.