View Full Version : SE testpoint doesn’t work
Recently I have activated the Dream SE part
The K320, W200 test point doesn’t work, even though I have fixed the cable.
I have also tried the k320, that reads well the info, but the test point doesn’t work here either.
I made an attempt with my colleague’s box and my cable, but without luck; then his cable with my box, again without luck.
His stuff works well with all kind of phones. Mine not; just with the Siemens part with Axx, Cxx, Mxx.
please help
GSM Dream
05-06-2008, 13:00
Hello!
Can you post logs from DBSS?
Recently I have activated the Dream SE part
The K320, W200 test point doesn’t work, even though I have fixed the cable.
I have also tried the k320, that reads well the info, but the test point doesn’t work here either.
I made an attempt with my colleague’s box and my cable, but without luck; then his cable with my box, again without luck.
His stuff works well with all kind of phones. Mine not; just with the Siemens part with Axx, Cxx, Mxx.
please help
CHECK YOUR TP CABLE MAYBE IT IS DEMAGE
CHECK YOUR TP CABLE MAYBE IT IS DEMAGE
Cable tested
my cable functionaly for DreamBox your coleg
Recently I have activated the Dream SE part
The K320, W200 test point doesn’t work, even though I have fixed the cable.
I have also tried the k320, that reads well the info, but the test point doesn’t work here either.
I made an attempt with my colleague’s box and my cable, but without luck; then his cable with my box, again without luck.
His stuff works well with all kind of phones. Mine not; just with the Siemens part with Axx, Cxx, Mxx.
please help
tespoint cable is ok but u r use fault brother . when w200 is connected then use access mode tespoint and go to security , Execute security by pass then show the pic testpoint connect to pin27 and with mouse click on show testpoint bottom start same as satge2 to testpoint on pin 37
U r br wait working same as simens br but in se click on start by mouse
Hello!
Can you post logs from DBSS?
dbss log:
www.fprima.ro/File/dbss.log
Cable, program, metod ..... tested with my colleague’s box
Hello!
Can you post logs from DBSS?
any solution :(
please help
bro tp is 27 for stage 1 and 37 for stage 2
cause in begin i do tp on 21 :/
MAYBE this is your problem
GSM Dream
05-07-2008, 13:36
dbss log:
www.fprima.ro/File/dbss.log
Cable, program, metod ..... tested with my colleague’s box
I can't see process for K320 or W200 in this log.
Can you send ALL *.log files from DBSS (Program Files->DreamBox)?
I can't see process for K320 or W200 in this log.
Can you send ALL *.log files from DBSS (Program Files->DreamBox)?
www.fprima.ro/File/dbss.log
www.fprima.ro/File/dbsserr.log
DreamSupporter
05-07-2008, 17:54
www.fprima.ro/File/dbss.log (http://www.fprima.ro/File/dbss.log)
www.fprima.ro/File/dbsserr.log (http://www.fprima.ro/File/dbsserr.log)
As I see from your logs:
....
--- Security Bypass------------------------------------------------------------
User selected phone K510 using Test Point boot mode
Stage 1 started
1) Turn OFF the phone.
2) Connect the phone to DreamBox cable.
Boot Responce = 5A
Processor ID = 8040030101010101 (DB2012 R3A)
Warning : Detected platform is different from selected
....
you selected K510. So probably you made mistake. You need to select K320 model if you work with K320. I don't see in logs that you was working with K320 or W200.
yesterday tested k510
suported model . . .
& not work
hy Dreambox suporter,
today tested W200, cid52
log:
www.fprima.ro/File/dbsserr_w220.log
www.fprima.ro/File/dbss_w200.log
tespoint 100% OK
GSM Dream
05-14-2008, 10:50
& not work
Please explain when you say "not work".
About K510.
I see important 2 messages in your last logs:
Error : Testpoint failed. Check pin and try again.
That's mean, that you connect to wrong pin or disconnect tp needle from it too early.
Error : Invalid GDFS structure and/or configuration.
Hint : Try to flash firmware.
If you will have this error after flashing again - nothing can be done.