Inned pinout of Bluetooth A1000.

[amol_sm]

Hello to all ,

I want pinout for A1000
2 Sim
1 MMC

Here is i attached the pic of this model. It is not too clear.

Thankx in advance.
:)

[amol_sm]

Hello to all ,

I want pinout for A1000
2 Sim
1 MMC

Here is i attached the pic of this model. It is not too clear.

Thankx in advance.
:)

OOOOOOpppppppppppppppppps dear it is A2000 not 1000.
:(

[amol_sm]

@ Infinity Team u don't have this model pinout . . . ?

[InfinityHelp]

hello!

is this phone MT62xx MCU based?
what connector does it have?

[amol_sm]

Yes sir It is MT62XX base phone.
& connector type is Smasung E250 as same.

[amol_sm]

@ Infinity Team . . .
Where r u................? Look at my post. 4 day's gone.
& after FOUR day's no reply.


What i understand Infinity Team . . . ?
If u can't see this type of model . . . . . ?
OR u don't have any pinout of this model.



Waiting for Reply.

[InfinitySupport]

Dearest Friend !

Could you, please, tell me, how many pins in this phone bottom connector.
Thank you very much for your kind patience and understanding !

http://www.infinity-box.biz/download/public/ads_AutoPinFinder1.jpg

[amol_sm]

The connector type of this model is like this.

http://hosting05.imagecross.com/image-hosting-05/1024NEC-N343i.JPG

But in this picture total pin of this connector is 10.
But On my phone total pin is 14.


Here is the attached image.

[amol_sm]

Please give me pinout of this model Infinity team.
Thankx in advance.

[InfinitySupport]

Hello,

Where is Gnd pin at phone connector ?

[amol_sm]

Hello,
Pin 3 - Gnd
Pin 11 - Gnd


Here is the pic of this connector.
Gnd set as pic serial number.

[amol_sm]

Sorry for the not posting clear phone model & connector phone.

[InfinitySupport]

Hello,

connector_2x7_mini

3: Gnd
6: Tx
13:Rx

connector 2x7
13: Gnd
14: Gnd
7: Tx
8: Rx

btw, did you tried to detect pinout with PinFinder ?

[amol_sm]

I have no pinfinder.
Also thankx for the pinout. I tryed & post result.



Thankx.

[amol_sm]

InfinitySupport,
I can't find any cable for this type of connector.
Did u seggest the name of any cable . . . ?


& another fact is i can't solder this connector point because it is too close.

[amol_sm]

Hello Infinity team,
I connect the phone to pin 6 & 7 & i try to rad out the detailed info.
Here is the error Log.

COM11 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 00
error: boot initialization step-3 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 80
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 80
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 00
error: boot initialization step-2 failed: 80
error: boot initialization step-2 failed: 20
error: boot initialization step-2 failed: D0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 00
error: boot initialization step-3 failed: 00
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 00
error: boot initialization step-2 failed: 00
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: A0
error: boot initialization step-2 failed: 0A
error: boot initialization step-2 failed: F0
error: boot initialization step-2 failed: F0
error: boot initialization step-2 failed: 00
19200 fixed
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 23 sec
Remove/Install battery now !

[amol_sm]

& also some time this error show
COM11 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
error: boot initialization step-2 failed: D0
19200 fixed
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 5 sec
Remove/Install battery now !

[InfinitySupport]

InfinitySupport,
I can't find any cable for this type of connector.
Did u seggest the name of any cable . . . ?


& another fact is i can't solder this connector point because it is too close.


I can not give you any advice about connector due to you need to check your cables by yourself. The only one I can say: you can use Infinity-Box Unicables or Infinity-Box PinFinder, both cables sets has 2x7 connectors.

[amol_sm]

OK i try my best @ moment.
But what is the log history.
I try to flash the phone many times but same error show..


Waiting for reply.

[InfinitySupport]

@amol_sm
both your previous logs show that your cable is incorrect (wrong Rx and/or Tx connected).
It's need to double check cable.

[amol_sm]

Hello,

connector_2x7_mini

3: Gnd
6: Tx
13:Rx

connector 2x7
13: Gnd
14: Gnd
7: Tx
8: Rx

btw, did you tried to detect pinout with PinFinder ?


I try to connet via this pinout but before i post log this error show.
And another thing is Gnd pin is only 3 & 11 not pin 13.



Any other pinout . . . . :confused:

[veerpreet]

bro........ 1st check cpu
2nd check conecter voltage
2.75
2.78 &3rd this voltage is rx tx 1000% success solution.
check then reply

[amol_sm]

bro........ 1st check cpu
2nd check conecter voltage
2.75
2.78 &3rd this voltage is rx tx 1000% success solution.
check then reply

I don't understand what u say.
Please more detail here . . . .



Thankx.

[InfinitySupport]

I don't understand what u say.
Please more detail here . . . .



Thankx.


As I can see you are in big troubles. Especiall for situations like yours we have prepared FAQ thread where you can see very detailed instruction how to find pinout in minutes:
http://www.gsmhosting.com/vbb/showthread.php?t=476373

And if you have many phones to repair I strongly suggest you to buy Infinity-Box PinFinder so you will be able to detect new pinouts in seconds.
Here is more information: http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf

[veerpreet]

bro.check the voltage from all pins the voltage of rx and tx will be 2.75 & 2.78
i will explain
1-0v
2-1.20v
3-0v
4-0v
5-3v
6-2.75v
7-0v
8-0v
9-1.20v
10-2.78v
11-0v
12-0v
13-0v
14-0v pin no 6 & 10 rx tx

[amol_sm]

PLEASE Infinity team tell me the another way to find this model pinout . . . :rolleyes:

Please also tell me where can i find this model pinout.
Thankx in advance.

[InfinityHelp]

hello!

if you dont have pinfinder- then only possible way for you is to measure voltage on all pins and detect tx/rx by voltage 2,7-2,9 volts,
just like mr. veerpreet said

[amol_sm]

But how could i measure this voltage InfinityHelp . . . ?
The phone is in dead condition & i try to check the voltage via putting the battry in the set.
But @connector none voltage show.

[andyvikas]

But how could i measure this voltage InfinityHelp . . . ?
The phone is in dead condition & i try to check the voltage via putting the battry in the set.
But @connector none voltage show.

Its difficult t find pinout in such cases.
One way of finding is to check voltages as soon as you press power on key.

Hope this helps...

Regards

[InfinityHelp]

hello!

first of all make sure that you use fully charged battery