8810 dvd dead

[jawal]

any help with 8810 dvd slide dead
can't do anythinq with this models
this the log
COM15 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
Action: read NAND flash
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND id: 00000000
ram size: 00800000
Initialize Fail
Finished, time used: 27 sec
Remove/Install battery now !
and if i want to do anything always message
error: Wrong model selected, select model: Autodetect 6228 NAND

[InfinitySupport]

Select model: Autodetect 6228 NAND and try to read flash.
What is the results ?

[jawal]

Where I Can Select This ?

[jawal]

sorry find it !!!!! will try and send report

[jawal]

when i read phone the result is

COM15 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND id: 00000000
ram size: 00800000
Initialize Fail
Finished, time used: 33 sec
Remove/Install battery now !

what happen i cant know what is the version of phone

[InfinitySupport]

According to your log file I can tell you that your phone has damaged hardware due to flash chip can not be detected.
You must open phone and repair it's hardware, f.e. reball flash chip and CPU chip as a first step.

[jawal]

COM15 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND: Samsung K9K1208X0C 512+16 32 pages, 66Mb
NAND id: EC76A5C0
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
error: no any expected answer
NOR: 0000:000000000000 [00000000]
NAND: 00EC:007600A500C0 [04200000]
NOR chip is not installed
Initialize Done
Set baud...
slowest
Set baud Done
Identification...
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
reading structure area...
error: unexpected answer:
warning: nfi read command is not accepted
error: structure area read failed, read again...
error: unexpected answer:
warning: nfi read command is not accepted
error: can't read area required for structure detection: 00000000 instead of 00010000
Finished, time used: 81 sec
Remove/Install battery now !
after rehoot cpu and flash chip
I think that the phone is death

[InfinityHelp]

hello!

still looks like hardware fault.
did you get last log after some repairing?

[jawal]

I Post The Last Log After Repairing Hardware So The Phone Is Death