One Chinesse Phone

[Mansoor]

This phone was bought to me when it is a dead set ZT 328
COM7 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6205:8B00]...
CPU: MT6205
high speed boot enabled
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #01 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #02 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #03 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #04 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #05 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #06 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #07 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
number of flash chip/regions detected: 08/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
detecting chip #01 in region #00...
flash: 01227E221A2201:30F78800000000
flash: Amd AMD/Fujitsu std [T 0008x002000 003Fx010000] 4Mb
it's time to stop: 301C88F739FC3078391CB9F698EB0120BCE70000F0B50F1C
number of flash chip/regions detected: 01/01
total flash region size: 00400000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00380000
flash: 01227E221A2201:30F78800000000
checking area[00000000]: 00000000-003FFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00380000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00080000
ffs chip: 00
eeprom/ffs area: 00000000:00380000-003FFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom]...
file saved: D:\Program Files\InfinityBox\ChineseMiracle\eeprom_20080621-164901.B0E.bin
flash: 01227E221A2201:30F78800000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
error: security area#1 communication fault
You can flash phone now but can't finalize it.
In most cases phone can NOT power-on normally.
Do you want to write flash anyway ?
Area: Firmware
flash: 01227E221A2201:30F78800000000
Write: Firmware
jump to next chip[01]
flash: 01227E221A2201:29EA0000000000
Write: Firmware
jump to next chip[02]
flash: 01227E221A2201:84211A00000000
Write: Firmware
I N T E G E R OVERFLOW