View Full Version : anoyone have this flash Trident MB-700
BesTCooL
06-23-2008, 14:34
Cpu1 : Ckt26_06b_pcb01_gprs_mt6226_s01.swan+_6226_yr_l6en _211_080129_ld0_0v0_sa75_ctf_bt.bin_d8c684fc_20080 623-150819
BesTCooL
06-24-2008, 13:47
up up upup up up
up up up
i have one Trident MB-700T
inside are 2 CPUs:
MT6205 and MT6226
but on PCB not write RX,TX.
i need RX,TX inouts for connector.
?
InfinityHelp
10-22-2008, 22:52
i have one Trident MB-700T
inside are 2 CPUs:
MT6205 and MT6226
but on PCB not write RX,TX.
i need RX,TX inouts for connector.
?
hello!
maybe pinout is hidden in system connector? what type it is?
pinout is 1x18 pins
i found rx and tx near CPUs. but can't read it:
this is ot MT6205:
COM12 [VCP0] selected
module v2.65
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6205:8B00]...
CPU: MT6205
high speed boot enabled
Connecting, wait...
only this. for other CPU MT6226 can't read it.
this is pictures on mobile:
this is wher try Format FFS: safe mode
COM12 [VCP0] selected
module v2.65
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6205:8B00]...
CPU: MT6205
high speed boot enabled
Connecting, wait...
error: can't finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 100 sec
Remove/Install battery now !
this is from "Read detailed information":
COM12 [VCP0] selected
module v2.65
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6205:8B00]...
CPU: MT6205
high speed boot enabled
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22022201:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: 01227E22022201:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: 01227E22022201:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #03 in region #00...
flash: 01227E22022201:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22022201:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: 01227E22022201:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 00800000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: SUNHIGH05_06A_PCB02_GSM_MT6205B_DN.X6_06_44_8312_V 1_23-TN-MP-4B-QN.BIN
ver. sw2: X6.06.44.8312.V1.23-TN-MP-4B-QN, 00000000
ffs offset/size: 00700000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00700000
flash: 01227E22022201:18E59F00000000
checking area[00000000]: 00000000-007FFFFF...
eeprom/ffs found near: 00700000
detecting eeprom/ffs size...
eeprom/ffs size: 00100000
ffs chip: 00
eeprom/ffs area: 00000000:00700000-007FFFFF
detecting ffs structure pass 1...
.......
detect standard fat location pass #1...
............
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
detecting ffs structure pass 2...
..........
detect standard fat location pass #1...
............
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #2 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
Finished, time used: 32 sec
Remove/Install battery now !
ok, on MT6205 i make Format FFS Complete but if phone is with SIM card after start and 5-10sec. turn OFF.
i can't make Format FFS Safe mode.
write IMEI only with mode-3. with mode-1 and mode-2 can't write IMEI.
how to fix this mobile ?
how to make Format FFS on MT6226 ? (i have it's rx and tx)
ok, phone is ready.
this is working inside-pinout.
tested.
InfinityHelp
10-23-2008, 23:10
hello!
thank you for sharing pinout!!!
I am glad that you solved this problem