15 Jul 2008: LG-KP220, Zonda-1075, Zonda-1085, MyPhone-S21 models under test

[InfinitySupport]

"MModule" v2.26 uploaded in support area:

.LG-KP220, Zonda-1075, Zonda-1085, MyPhone-S21 models under test

We are waiting for test reports

KP220 cable:
keyboard top
1.........18
1: Gnd
2: phone Rx (RJ45 pin-2)
3: phone Tx (RJ45 pin-3)
5: Gnd
15: Gnd
18: Gnd

We are looking for KP320 model for test so if somebody has it and ready to sell for research, please, contact to Infinity-Box forum member.

[Faisal_Computer]

Thanks for the Great work as soon i got any mobile i will test and post you results

Br

Faisal_Computer

[sahil2000ind]

Thanks For The Update Keep It Up Infinity Team

[asad_nomy7]

very nice update specilay for KP220.

[zahid_gsm]

"MModule" v2.26 uploaded in support area:

.LG-KP220, Zonda-1075, Zonda-1085, MyPhone-S21 models under test

THANX

[nasirkhan007]

nice update keep it up

[Miftahudin]

very nice work keep it up...........

[delchoni]

again add more power to infinity ................








br.

[SHOEB AHMED]

GOOD
very nice update

[Brod Aries]

my phone is alive again!!! thanks for update infinity team...

flashing logs...

COM23 [VCP0] selected
Device: MyPhone-S21
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6223:8A04]...
CPU: MT6223
chip: 0011:1AB6:000C
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 damaged, recalculation required
identification#1 detection finished
device-id: F28A745A
identification#1 protocol ver: 04
ver. sw1: TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN
ver. sw2: T01_23.07A.W0736.MP.FMCAM-FTP_V0.07, 7B10017A
ffs offset/size: 00800000/00800000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom[TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN]]...
file saved: C:\Program Files\InfinityBox\MModule\eeprom[TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN]_20080715-163912.B0E.bin
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
Area: Firmware
flash: 01227E22202200:2AEA0000000000
Write: Firmware
Area: Eeprom/ffs
flash: 01227E22202200:2AEA0000000000
Write: Eeprom/ffs
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization...
Finalization Done
Finished, time used: 1739 sec
Remove/Install battery now !

br

[Brod Aries]

after unlock still INSERT SIM appears on screen.

COM23 [VCP0] selected
Device: MyPhone-S21
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: unlock
unlock method: standard
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6223:8A04]...
CPU: MT6223
chip: 0011:1AB6:000C
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\MModule\backup_security\id.F28A7 45A.[TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN_85FEEF84].rpl
identification#1 detection finished
device-id: F28A745A
identification#1 protocol ver: 04
ver. sw1: TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN
ver. sw2: T01_23.07A.W0736.MP.FMCAM-FTP_V0.07, 7B10017A
ffs offset/size: 00800000/00800000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom[TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN]]...
file saved: C:\Program Files\InfinityBox\MModule\eeprom[TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_07.BIN]_20080715-172543.B0E.bin
flash: 01227E22202200:2AEA0000000000
Backup required data Done
Patch required data...
detection procedure, wait...
detection procedure completed
detection procedure, wait...
detection procedure completed
Patch required data Done
Special operation...
Special operation Done
Write...
flash: 01227E22202200:2AEA0000000000
Write: eeprom
Write Done
Finalization...
Finalization Done
file saved: C:\Program Files\InfinityBox\MModule\system_log_F28A745A_TINN O23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736_MP_ FMCAM-FTP_V0_07.BIN_85FEEF84_20080715-173101.B0X.bin
Finished, time used: 1186 sec
Remove/Install battery now !

br

[InfinitySupport]

@Brod Aries
Are you sure that phone is locked but not have hardware problems ?
We need to get so detailed problem description as possible

[Brod Aries]

i tried other sim with pin code enabled, upon power on it asked for pincode then i enter after accepting pincode INSERT SIM appears. ;)

i also tried TEST CARD still INSERT SIM appears but if you put its original sim it accept and works perfect.

br

[OUSKHMANE]

very nice update ......................

[InfinitySupport]

i tried other sim with pin code enabled, upon power on it asked for pincode then i enter after accepting pincode INSERT SIM appears. <IMG class=inlineimg title=wink alt=\"\" src=\"../ubb/wink.gif\" border=0 smilieid=\"5\">

i also tried TEST CARD still INSERT SIM appears but if you put its original sim it accept and works perfect.

br

Hello,

What network your phone is locked ? I mean network name and MCC/MNC.

[Cellcraft India]

I was waiting,update for LG KP 220.I have this phone with me.I'll test and post results tomorrow.Thanks for the updates.:):):)

[nasermmx]

infinity plz update huawai d1000

[josh_aina]

Hi!
Thank you very much bro. I wait for Haier hg-m101 (flash & sp unlock)

[InfinitySupport]

infinity plz update huawai d1000

Hello,

Here is some information: http://www.gsmhosting.com/vbb/showthread.php?t=546293 (http://www.gsmhosting.com:80/vbb/\"http://www.gsmhosting.com/vbb/showthread.php?t=546293\")

[Brod Aries]

hello,

What Network Your Phone Is Locked ? I Mean Network Name And Mcc/mnc.

Globe Philippines 515-02.

Br

[beans]

Globe Philippines 515-02.

Br


when you see in details this s21 phone not locked but why cant accept others simcard only insert simcard maybe paching can help and original flashfiles not locked.

imei: 35439101600196
connection Ok
157 byte(s) read
Phone lock: Off
Network lock: Off
Network subset lock: Off
Service provider lock: Off
Corporate lock: Off
IMSI lock: Off
Auto lock: Off
Phone code: 1122
Finished, time used: 12 sec
Remove/Install battery now !

[Parminder Singh]

thanks great support infinity box



PARMINDER SINGH

[Cellcraft India]

LG KP 220 tested using Infinity MModule v2.26,its working fine

I used Pin finder to connect the set.It worked for me when i set Rx = 3 and Tx = 2,also selected reverse pin numbering option.

Tested following

1) Full flash read
2) User code unlock
3) IMEI change :D ( it worked for me with mode 2 )

Logs follows.............


Full flash read
---------------
COM16 [VCP0] selected
Device: LG-KP220
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6219:8B02:8B01]...
CPU: MT6219
CPU: MT6226MA detected
chip: 0031:A9C1:EECE
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 98004900000002:29EA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7338IN00-001-R1S.BIN
ver. sw2: 7S7338IN00-001-R1S, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [flash[ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7338IN00-001-R1S.BIN]_part_1_of_1]...
file saved: C:\Program Files\InfinityBox\MModule\flash[ARIMA26_05C_PCB01_GPRS_MT6226M_S01.7S7338IN00-001-R1S.BIN]_part_1_of_1_20080716-005210.B0X.bin
Finished, time used: 1735 sec
Remove/Install battery now !


User code unlock
----------------
COM16 [VCP0] selected
Action: read codes
unlock method: read codes
Model: LG-KP220
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6219:8B02:8B01]...
CPU: MT6219
chip: 0031:A9C1:EECE
CPU: MT6226MA detected
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6219B,E02
Date: 2005.04.12
Version: 1.0
Version: 7S7338IN00-001-R1S
Version: EP_0920
60 byte(s) read
imei: 3514*********XX
connection Ok
208 byte(s) read
Phone lock: On
Network lock: Off
Network subset lock: Off
Service provider lock: Off
Corporate lock: Off
IMSI lock: Off
Auto lock: Off
Phone code: 25846F
Finished, time used: 11 sec
Remove/Install battery now !

IMEI change
-----------
COM16 [VCP0] selected
Action: imei
imei write method: mode-2
new imei: 3514*********XX
Model: LG-KP220
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6219:8B02:8B01]...
CPU: MT6219
chip: 0031:A9C1:EECE
CPU: MT6226MA detected
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6219B,E02
Date: 2005.04.12
Version: 1.0
Version: 7S7338IN00-001-R1S
Version: EP_0920
60 byte(s) read
imei:3514*********XX
connection Ok
60 byte(s) read
verification...
verification done: 3514*********XX
Finished, time used: 10 sec
Remove/Install battery now !


Thanks to infinity for this updates.................:)

[KHJAMAL]

Thanks For The Update Keep It Up Infinity Team

[Brod Aries]

Hello,

What network your phone is locked ? I mean network name and MCC/MNC.



hi...
i received 1 unit myphone s21 yesterday with INSERT SIM with all providers here, i fixed it with flashing main and eeprom from support and it fixed it, as ussual the phone only accepts its original sim.;)

br

[kasamiko]

Nothing new bro...

just wait for updates on S21..

[ayasir83]

very very good work infinity team

[angelcelu]

Zonda 1085 after flasheo puts white screen and off

evice: Zonda-1085
Done
Loading file v.02...
Zonda-1085_E501_ZONDA_PCB01_GPRS_MT6226_S01[1].E501.06A.W06.36.MP.V36.F2_2007-12-20_En_Es.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw1: E501_ZONDA_PCB01_GPRS_MT6226_S01.E501.06A.W06.36.M P.V36.F2.BIN
ver. sw2: E501.06A.W06.36.MP.V36.F2, 00000000
detecting languages...
Languages: En Es
Loading file v.02...
Zonda-1085_ffs_01[1].B0E.bin loaded
COM2 [VCP1] selected
Device: Zonda-1085
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
chip: 0031:DC6E:DE76
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: B0001D00000000:B0001D00000000
flash: Sharp Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: E501_ZONDA_PCB01_GPRS_MT6226_S01.E501.06A.W06.36.M P.V26.F1.BIN
ver. sw2: E501.06A.W06.36.MP.V26.F1, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom[E501_ZONDA_PCB01_GPRS_MT6226_S01.E501.06A.W06.36.M P.V26.F1.BIN]]...
file saved: C:\Archivos de programa\InfinityBox\MModule\eeprom[E501_ZONDA_PCB01_GPRS_MT6226_S01.E501.06A.W06.36.M P.V26.F1.BIN]_20080721-173132.B0E.bin
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Area: Firmware
flash: B0001D00000000:B0001D00000000
Write: Firmware
Area: Eeprom/ffs
flash: B0001D00000000:B0001D00000000
Write: Eeprom/ffs
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization...
Finalization Done
Finished, time used: 997 sec
Remove/Install battery now !

[andy_lecnah]

great updates infinity support....:):):)

[rameez_gsm]

wow nice update infinity always go update

[InfinitySupport]

@angelcelu
please, double check phone battery voltage, it may be that battery become empty after flash.
Also there is a reason to make firmat ffs operation

@Brod Aries
@kasamiko
@beans
Can you sell to us one S21 phone for detailed research ?

[alfox]

Yeah were waiting for the s21 update.can someboday sell the unit to infinity team?i have here my personal phone.i bought this for the purpose of testing it for infinity unlock.

[abdulhakeem]

nice update a perfect update it is............................

keep it up......................infinity team.

[kasamiko]

Yeah were waiting for the s21 update.can someboday sell the unit to infinity team?i have here my personal phone.i bought this for the purpose of testing it for infinity unlock.

Benta mo na pre...why not sell it to infinity team for testing..hehehe

[shahanwer]

please help me kp220 rx tx pin outs????????????????

[shahanwer]

TOOOOOOOOOOOOOOO----------GOOD
very nice update FOR KP-220

[InfinitySupport]

please help me kp220 rx tx pin outs????????????????

Here is an information http://www.infinity-box.com/doc.php#9

[corts]

i have here my phone s21 u can contact me infinity team at my ym coma_cell@yahoo.com.

[corts]

it is lock to globe telecom network here in philippines

[benjycool]

Hi

im trying to reset user code of a zonda zmem1075 of telcel, which cable i need to use, please help, do i need to buy pin finder?

thank u.;)

[InfinitySupport]

Hi

im trying to reset user code of a zonda zmem1075 of telcel, which cable i need to use, please help, do i need to buy pin finder?

thank u.;)

Hello,

PinFinder is more easy way to serve different phones with new cables/connectors, but you can build cable by yourself without PinFinder.

Here is an instruction how to get cable/pinout information:

1. be sure that you have downloaded and installed latest Infinity-Box Pinouts update
2. run Infinity-Box Shell
3. select required model
4. see detailed information about cable/pinout (Rx/Tx/Gnd pins and other information)

Here is an example of information given by Infinity-Box Shell:

http://www.infinity-box.com/download/public/Infinity-Box_shell_v126.jpg

Here is information how to build your own cable:
http://www.gsmhosting.com/vbb/showthread.php?t=342807