V50 F0.14.04 with tampered alert

[caramelo99]

Hi!

I have a V50 F0.14.04 with tampered alert, and I need a full flash

for v50, does anyone have any full flash for this model (It´s

about 10 Mb, I think)?

Thank´s!

[dsimka]

it is 4 MB i think :-)
contact me on ICQ# 100687

[landy]

-You can´t flash xx.14xx phone in tampert alert state, because you need to know where is the test point for this model, and i´m sure that it isn´t where the old models.

BR Landy.-

[caramelo99]

Hi!

I have a v50 f0.14.04 that was tried to unlock with the old clip,

and now it's with Tampered Alert.

I have a Emmi++ and his board still has the test point.

What should I do to repair it?

What full flash should I use?

Can somebody send me that full flash...

Thank's in Advance!

[noone0]

just look at this

I think you have dead V50, because flash ID is 00000000. Some of
these f..ing phones die after using Test Point, the reason is UNKNOWN!
Osvaldas

--- In gsmhacking_new@y..., "Father Sandi" <sando@h...> wrote:
> Upload full flash with pemaster. Enter phone in bootstrap with test
point first , that's all
> ----- Original Message -----
> From: Project_One
> To: United_Gsmhacking@y... ; gsmhacking_new@y... ; gsmhack-
crew@y...
> Sent: Thursday, September 26, 2002 5:02 PM
> Subject: [gsmhacking_new] motorola V50 downgrading problem
>
>
> Hello Group,
>
> i´ve downgraded successfully a few V50 version xx.14.xx to lower
(xx.13.xx) version, but with one phone it´s not working.
> i´m working with Emmi2D(64mb) and MotoFlex8.01 and that´s the
error-message in Motoflex:
>
> ERROR: Flash part unsupported!!
> Mfg+Part Number Identified as : 00000000
> Part in radio not currently supported!
>
> software version of this phone is FO.14.04
>
> I´ver also tried with PeMaster, but without success.
> Any help will be much appreciated.
>
> Thanks in advance.
>
> Best Regards,
>
> Project_One

[crossings]

i have quite same porblems...
i tryed to flash t180 with pemaster ..checksum error.... and now with test point its tells "" unknown flash id:00000000

any solution ?

[felix]

hi,
i solve the tamper allert using tau and mera952 or mera960
by dan constantinescu, the sectret eas to suply the flash from tau key with +5V external suply. otherhow after phone finish the boot seq and the black lcd test apears> the comunication between box and phone desapeared.
the clear tamper worked after ext suply, but if i try to unlock with
xx13xx, after 00000000# wrong code, tamper again...

what to do with it? exists unlock sol for xx14xx?
yes or no?

the phones with xx14xx are equiped with same 2Mb flash cip but
a intel one, the cpu is diferent one, looks biger, amd the test
point is in oposite position than xx13xx. if +3,6V at test, low mode
ok, but same wrong flash ID, needs diferent boot loaders.
reply if you have any info about. or any eperience.
thanks,
felix.

[dsimka]

use pemaster+full flash 4MB -example f0.13.09 ,flash it using testpoint and that is ... correct IMEI and unlock pressing U :-)

[thecult]

If I flash with f0.10.xx using testpoint and later correcting imei I could unlock it withouth problem?

[dsimka]

but use full flash /include eeprom zone/ 4 MB size

[Siemens man]

hi dsimka
wich box using and how upload 4mb file. this file hex or bin file??
i have emmi box-2d. and how use bin file 4mb. thi is file possible using in labtool?????

[dsimka]

roemmi2 and pemaster , bin file
i dont know about full emmi - i dont have :-)

[Siemens man]

need hex file vF0.13.09 for emmi box. any one help me.
thank you

[VELIKI]

where can i download fullflash for pemaster in bin.format
thanks

[dsimka]

icq#711044

[Bohosh]

I have this file vF0.13.09.bin
PSService@mail.bg