plez help i-mobile 306 Set dead after Flash

[SHOEB AHMED]

i-mobile 306 Set dead after Flash


log
COM7 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6217:8A00]...
CPU: MT6217
high speed boot enabled
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22022201:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: 01227E22022201:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: 01227E22022201:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #03 in region #00...
flash: 01227E22022201:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22022201:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: 01227E22022201:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 00800000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00700000
flash: 01227E22022201:29EA0000000000
checking area[00000000]: 00000000-007FFFFF...
eeprom/ffs found near: 00700000
detecting eeprom/ffs size...
eeprom/ffs size: 00100000
ffs chip: 00
eeprom/ffs area: 00000000:00700000-007FFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
flash: 01227E22022201:29EA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: 01227E22022201:29EA0000000000
Finalization Done
Finished, time used: 56 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

[InfinitySupport]

Hello,

Try to repeat operation at 115200 baudrate and disable \"format FFS\" during flash process.

Question: what was with phone BEFORE flashing ?

[SHOEB AHMED]

Question: what was with phone BEFORE flashing ?

AN/... late power on but phone hang fiw sc power off

[SHOEB AHMED]

BEFORE FLASHING...............
Take long time to power on but hang and after few second auto power off.


PLEASE HELP ME SUPPORTER OR ANYBODY.



shoeblsc@yahoo.co.uk
shoebxp@gmail.com


BR

MZONE

[InfinitySupport]

You need to open phone and check it\'s hardware, f.e. reball flash IC