View Full Version : need sprint s60 flash file
unlock & flash
08-21-2008, 12:43
need sprint s60 infinity formate tested flash file
pls any one share with me
need sprint s60 infinity formate tested flash file
pls any one share with me
post your infinity ditels log, or read C:\Program Files\InfinityBox\ChineseMiracle
then read your phone log & post it.
InfinityHelp
08-21-2008, 23:32
hello!
yes, please post your phone software version readed in "read detailed information" mode
alamgir80
08-22-2008, 03:51
Don't detect fimware ver. I,m try with brand new sprint s60. Read full flash & eeprom no problem. Pinout same sprint 7700.
InfinityHelp
08-22-2008, 22:39
hello!
try in "read general information" on powered On phone
alamgir80
08-23-2008, 06:02
cm ver 2.59
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6217:8A00]...
CPU: MT6217
high speed boot enabled
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 01227E22212200:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00800000
Detected eeprom/ffs address is non-standard: 00800000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00800000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 00800000
ffs chip: 00
eeprom/ffs area: 00000000:00800000-00FFFFFF
detecting ffs structure pass 1...
............
detect standard fat location pass #1...
................................
detect extended fat location pass #1...
............
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
detecting ffs structure pass 2...
............
detect standard fat location pass #1...
................................
detect extended fat location pass #1...
............
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #2 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
Finished, time used: 62 sec
Remove/Install battery now !
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
baud set to: 19200
error: connection failed !
Operation failed !
Finished, time used: 78 sec
Power off phone now !
SHOEB AHMED
08-23-2008, 14:59
tested flash file Download Link
http://rapidshare.com/files/119233238/Sprint_S60.rar
alamgir80
08-23-2008, 17:40
tested flash file Download Link
http://rapidshare.com/files/119233238/Sprint_S60.rar
my phone is ok, but my question why don,t detect firmware version?
SHOEB AHMED
08-23-2008, 17:49
see....................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
InfinityHelp
08-23-2008, 22:14
hello guys!
very few phone models do not show firmware version in boot mode.
in this case "read general information" must be used
bashiruddinlkte
11-09-2008, 13:32
thanksssssssssssssssssssssssssssss
All time says damage file whats this???
Br
Mahadi
unlock & flash
11-17-2008, 08:58
i have infinity formate sprint s60 flash file
if need contact with me
bashiruddinlkte
11-18-2008, 09:46
i have infinity formate sprint s60 flash file
if need contact with me
flash file
http://rapidshare.com/files/164911784/file_S60.rar.html
loader
http://rapidshare.com/files/164912819/s_60_lodar.rar.html
:D
sumon.bd
12-07-2008, 14:11
tested flash file Download Link
http://rapidshare.com/files/119233238/Sprint_S60.rar
phone is ok nice share!!!
another link please...................