View Full Version : Emmiclip Instructions Pplleaassee!
I'M NEW TO MOTOROLA PHONES,I BOUGHT EMMICLIP V2 FOR VXX.13.XX PHONES BUT CAME WITH NO INSTRUCTIONS.PLEASE SEND ME INSTRUCTIONS A.S.A.P
THANX
2. Operation Introduction
I. Unlock SP and special lock for old xx.13.xx version mobile phones
Install the 9V battery into the battery compartment, then press the red button and power on the EMMI clip in meantime, then release the red Button, the Red LED power indicator will light and the Green LED indicator will flashing once. After the clip auto-animation, connect the mobile phone to the clip and power on the phone; the green LED will light up for about 4-5 seconds and then goes to flashing. Then SP lock and SIM lock has been removed successfully.
II. Unlocking for new versions mobile phones
Fix and power on the clip, the red and green LED indicators will light up. Insert the SIM card into mobile phone and connect it to the clip; Make sure the connectivity well, then press the red button and Power on the mobile phone in meantime, the Green LED indicator will light up for a few seconds; then the mobile phone will power off automatically. Release the red button and then power on the mobile phone; The phone screen will display “ TEST TAMPER ALERT ”; then input “00000000” and press “OK” button, the 8-bit special code and net lock have been unlocked already.
Caution: 1. Use fresh 9V battery if the EMMI clip cannot work well. 2. The mobile phone’s battery must be charged in full condition. 3. Once the operation failed, please try again steps by steps.
Operation instruction for unlocking T192 by V11 EMMI clip as below.
We would like to send you some tips about our V11 EMMI clip as below for your reference. Just follow the instruction we listed below, and you can solve all problem on T192 mobile phones. Just a reminder, you have to wait the Green LED of EMMI clip stopping flash, then you can go to next step of operation.
Please kindly find the detail operation instruction for unlocking T192 as follows:
Step 1 : Turned the T192 phone power OFF,
Step 2 : Connect the T192 mobile phone to the EMMI clip by using the T192 cable connector
Step 3 : Turn the EMMI clip power " ON"
Step 4 : Then pressing the "Red" button of the EMMI clip (just keeping to press the "Red" button until the T192 mobile phone turn OFF automatically), then turn the T192 mobile phone power "ON". The screen of T192 mobile phone will light up for several seconds, then the power of T192 mobile phone will be turned OFF automatically. and waiting the Green LED of EMMI clip stop flashing. Just a reminder, please keep to pressing the "Red" button of EMMI clip during entire Step 4 until the T192 mobile phone turns OFF automatically.
Step 5: Release the "Red" button of the EMMI clip.
Step 6 : Insert SIM card into the T192 mobile phone, turn the T192 mobile phone power "ON", and the screeen of mobile phone will ask you to input 8 digits code, please wait the Green LED of EMMI clip stopping flash, then you input "00000000", then press "OK" button of the mobile phone, and then the T192 mobile phone will be worked as normal. Just remider, please wait the Green LED of EMMI clip stopping flash before you input "00000000" to the T192 mobile phone.
NOTE: IT IS VERY IMPORTANT PROCEDURE TO WAIT THE GREEN LED STOPPING FLASH, THEN YOU INPUT THE 8 DIGITS ZERO.
Step 7 : Turn the T192 mobile phone OFF, and take the T192 mobile phone disconnect from EMMI clip, then turn the T192 mobile phone power ON, all problem solved.
Remark: you may repeat from step 1 to step 7 for several times if the phone goes wrong.
If your Emmi clip have a red pushbutton the description of cobba is correct ! This emmi clips with red pushbutton have supertrio firmware and they do most of the T192 versions, except the newest ones.
If your Emmi clip does not have any pushbutton on the cover, this clips have Zulea firmware inside and they DO NOT ALL T192 and of course also not the newest ones. For the Emmiclips without pusbutton (Zulea´s), please use the follow instructions:
**************************************************
Prepair EMMI Clip to work:
1. Connect one 9v battery to the EMMI Clip.
2. Power on the CLIP from on/off switch
3. The power on state is indicated by the Red LED
4. After power on, wait ~2 seconds until Green LED will blink fast for 1 second.
5. Now the EMMI Clip is in IDLE satte and ready to work.
Unlocking old version of Motorola phones:
1. Phone must be powered off.
2. Connect the phone with right cable to the EMMI Clip
3. Power on the phone. Right after power on, the Green LED will light.
4. Wait until Green LED start blink slow.
5. Power off the phone.
6. Now the phone is unlocked.
Unlocking NEW veriosns (xx.13.xx) of Motorola phones:
1. Phone must be powered off and with SIM card inside.
2. Connect the phone with right cable to the EMMI Clip
3. Power on the phone. Right after power on, the Green LED will light.
4. Wait until Green LED start blink fast.
5. If phone say TAMPER ALERT, power off and repeat from step 3.
6. Now the phone ask to enter Special Code.
7. Please enter “00000000#”. The phone will display “Completed”. If the phone display “Wrong code” power off and repeat from step 3.
8. Power off the phone.
9. Now the phone is unlocked.
Note:
It is possible to be necessary to repeat step 3-7. That happens usualy when phone was try to unlock by other persons with small RoEMMI or with Full EMMI 2D. Repeating step 3-7 will finally clear the problem. On Phones ‘not touched’ before, is enough to make all operation one time to remove Network Lock (SP Unlock).
**************************************************
BE CAREFULL!!!
Many chinese suppliers wich offer emmi clips with red button or without button, claims that the clips do also change IMEI ! THIS IS WRONG! NO ONE OF THEM DO CHANGE IMEI!! not Zulea´s and not ours (the ones with red pusbutton)
Thanks, very detailed information by Cobba & Raskal
:-)
how do you check for the software version on t192 , v50 ,8088 etc
@ahmed
insert test card and press # so long until you see on screen "test"
than insert 19# and you can see the software version
Very usefull info! But... what about security, unlock code? And IMEI changing? Can emmi 2 with red button do these? Thx
gsmsalers
11-17-2002, 14:34
Hi.
I have trouble with unlocking t192 with EMMICLIP V2 FOR VXX.13.XX . I do same procudere as cobba. But when I try step 6 it doesn't ask for special code just logon network after pin code. If I disconnect it from emmi then step 7 it ask for special code. I entered 00000000 ok,then after 2 try it start beeping became tamper alert. What can I do?
Originally posted by gsmsalers
Hi.
I have trouble with unlocking t192 with EMMICLIP V2 FOR VXX.13.XX . I do same procudere as cobba. But when I try step 6 it doesn't ask for special code just logon network after pin code. If I disconnect it from emmi then step 7 it ask for special code. I entered 00000000 ok,then after 2 try it start beeping became tamper alert. What can I do?
But do your box have a red button or not?
gsmsalers
11-18-2002, 03:31
Yes.
Red button have.
Than download instructions, from our home page! Follow all step by step, it works!!!
gsmsalers
11-18-2002, 18:57
RaSkAl
Hi.
Where is your clip instructions from your home page?I can't find anything. Please put shortcut to it.
Thanks.