i need help for find pinout

[geti]

i have one phone and not have pinfinder
i need pinout phone is dual sim cpu type 6226BA
conector 1x20 and write N 328
PLEEASE HELP IS VERY VERY URGENT :confused:

[Shakeel_pattoki]

brother open ur fone.
see where is rx/tx printed on pcb.






.:::pinoutGuiders::.

[geti]

i open the phone and i not find there i have only vbb,power on off and pbp

[.::skybird::.]

i have one phone and not have pinfinder
i need pinout phone is dual sim cpu type 6226BA
conector 1x20 and write N 328
PLEEASE HELP IS VERY VERY URGENT :confused:


Is there no any company name (Nokia, cect......etc)?
plz show here to get pinout.









.::Pinout Guiders::. (http://www.forum.gsmhosting.com/vbb/group.php?groupid=55)
.::skybird::.

[Shakeel_pattoki]

if u have no success.
please read this thread carefully and do as.


http://www.gsmhosting.com/vbb/showthread.php?t=544521
http://www.gsmhosting.com/vbb/showthread.php?t=476373







..::PinoutGuiders::..

[InfinityHelp]

hello!

1. set multimeter to voltage measuring.
2. set one multimeter probe to some grounded phone part
(if you cant find grounded part outside phone- you need to take out small thin wire from negative battery terminal)
3. with second probe touch one by one all phone pins (phone battery attached)
(to get better result i would advice to set needle on the end of second probe)

memorise pins with voltage between 2,7-2,9volts.
those are tx/rx

[geti]

hi
my problem solved thanks INFINITYHELP and SHakeel_pattoki
for info now pinout is
conector1..............20
keypad top
19 20 GND
7 RX
8 TX:D:D:D

[geti]

here is logo
COM5 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:9719:9DBD
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: D09_LY_MT6226_V_237.BIN
ver. sw2: V_2.3.7, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading: flash[D09_LY_MT6226_V_237.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\N328\flash[D09_LY_MT6226_V_237.BIN]_20080913-095502.B0M.bin
Finished, time used: 435 sec
Remove/Install battery now !
:D:D

[Shakeel_pattoki]

thank u geti brother very much.
and congrats for doing a big job that u have done.




Good Luck.



.::PinoutGuiders::.