Freshbol
09-12-2008, 19:30
I try all modes but can't help
==== log: [12.09.2008 16:59:02] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-1)...
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19error:
detection failed (20 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 87 sec
Remove/Install battery now !
==== log: [12.09.2008 17:01:01] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-2)...
1 2 3 4 5 6 7 8 9 10 11 done
146 byte(s) read
reading data#2...
reading data#3...
error: operation failed !
Finished, time used: 46 sec
Remove/Install battery now !
==== log: [12.09.2008 17:01:59] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
done
158 byte(s) read
writing data...
verification...
error: verification failed
Finished, time used: 18 sec
Remove/Install battery now !
After, I find some firmware from support and flash it...
==== log opened: [12.09.2008 17:31:55] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.59
S/N: 0F4A:0110
Wait...
Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
CM_Nokia-E86-2sim_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YT CQYR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT_16m_En_Ru _Fr_Th_Vn_Farsi_Ar.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw1: CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN
ver. sw2: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT, 435B322F
You have loaded file with security features enabled.
detecting languages...
Languages: En Ru Fr Th Vn Farsi Ar
==== log: [12.09.2008 17:34:00] ====
COM3 [Serial2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 2C0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.1946A263.[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4BC].rpl
identification#1 detection finished
device-id: 1946A263
identification#1 protocol ver: 04
ver. sw1: CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN
ver. sw2: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT, 435B322F
ffs offset/size: 00F00000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00F00000
flash: 01227E22212200:2CEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00E00000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading: eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]_20080912-173646.B0E.bin
flash: 01227E22212200:2CEA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-173705.B0X.bin
Area: Firmware
flash: 01227E22212200:2CEA0000000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-173715.B0X.bin
Finished, time used: 175 sec
Remove/Install battery now !
I repeat touchscreen colibration
==== log: [12.09.2008 17:38:04] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-2)...
1 2 3 4 5 6 7 8 9 10warning: wrong packet cs
11 done
172 byte(s) read
reading data#2...
reading data#3...
error: operation failed !
Finished, time used: 51 sec
Remove/Install battery now !
==== log: [12.09.2008 17:39:04] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
done
158 byte(s) read
writing data...
verification...
error: verification failed
Finished, time used: 17 sec
Remove/Install battery now !
After I repeat flashing with uncheck "smart write"
==== log: [12.09.2008 17:40:41] ====
COM3 [Serial2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 2C0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.1946A263.[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4BC].rpl
identification#1 detection finished
device-id: 1946A263
identification#1 protocol ver: 04
ver. sw1: CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN
ver. sw2: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT, 435B322F
ffs offset/size: 00F00000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00F00000
flash: 01227E22212200:2CEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00E00000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading: eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]_20080912-174216.B0E.bin
flash: 01227E22212200:2CEA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-174227.B0X.bin
Area: Firmware
flash: 01227E22212200:2CEA0000000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-175014.B0X.bin
Finished, time used: 567 sec
Remove/Install battery now !
Last step - touchscreen colibration
==== log: [12.09.2008 17:51:07] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
done
158 byte(s) read
writing data...
verification...
error: verification failed
Finished, time used: 18 sec
Remove/Install battery now !
After all this operations touchscreen calibration w/o fixing.
==== log: [12.09.2008 16:59:02] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-1)...
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19error:
detection failed (20 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 87 sec
Remove/Install battery now !
==== log: [12.09.2008 17:01:01] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-2)...
1 2 3 4 5 6 7 8 9 10 11 done
146 byte(s) read
reading data#2...
reading data#3...
error: operation failed !
Finished, time used: 46 sec
Remove/Install battery now !
==== log: [12.09.2008 17:01:59] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
done
158 byte(s) read
writing data...
verification...
error: verification failed
Finished, time used: 18 sec
Remove/Install battery now !
After, I find some firmware from support and flash it...
==== log opened: [12.09.2008 17:31:55] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.59
S/N: 0F4A:0110
Wait...
Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
CM_Nokia-E86-2sim_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YT CQYR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT_16m_En_Ru _Fr_Th_Vn_Farsi_Ar.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw1: CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN
ver. sw2: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT, 435B322F
You have loaded file with security features enabled.
detecting languages...
Languages: En Ru Fr Th Vn Farsi Ar
==== log: [12.09.2008 17:34:00] ====
COM3 [Serial2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 2C0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.1946A263.[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4BC].rpl
identification#1 detection finished
device-id: 1946A263
identification#1 protocol ver: 04
ver. sw1: CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN
ver. sw2: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT, 435B322F
ffs offset/size: 00F00000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00F00000
flash: 01227E22212200:2CEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00E00000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading: eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]_20080912-173646.B0E.bin
flash: 01227E22212200:2CEA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-173705.B0X.bin
Area: Firmware
flash: 01227E22212200:2CEA0000000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-173715.B0X.bin
Finished, time used: 175 sec
Remove/Install battery now !
I repeat touchscreen colibration
==== log: [12.09.2008 17:38:04] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-2)...
1 2 3 4 5 6 7 8 9 10warning: wrong packet cs
11 done
172 byte(s) read
reading data#2...
reading data#3...
error: operation failed !
Finished, time used: 51 sec
Remove/Install battery now !
==== log: [12.09.2008 17:39:04] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
done
158 byte(s) read
writing data...
verification...
error: verification failed
Finished, time used: 17 sec
Remove/Install battery now !
After I repeat flashing with uncheck "smart write"
==== log: [12.09.2008 17:40:41] ====
COM3 [Serial2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 2C0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.1946A263.[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4BC].rpl
identification#1 detection finished
device-id: 1946A263
identification#1 protocol ver: 04
ver. sw1: CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN
ver. sw2: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT, 435B322F
ffs offset/size: 00F00000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00F00000
flash: 01227E22212200:2CEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00E00000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading: eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQYR_ L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN]_20080912-174216.B0E.bin
flash: 01227E22212200:2CEA0000000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area#1 calculation...
done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-174227.B0X.bin
Area: Firmware
flash: 01227E22212200:2CEA0000000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_1946A2 63_CKT26_06B_PCB01_GPRS_MT6226_S01.SWAN+_6226_YTCQ YR_L7EN_227_071106_LD0_0V0_SA75_CTF_BT.BIN_D0CDA4B C_20080912-175014.B0X.bin
Finished, time used: 567 sec
Remove/Install battery now !
Last step - touchscreen colibration
==== log: [12.09.2008 17:51:07] ====
COM3 [Serial2] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:87DA:5867
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: SWAN+_6226_YTCQYR_L7EN_227_071106_LD0_0V0_SA75_CTF _BT
Version: SWAN_6226
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
done
158 byte(s) read
writing data...
verification...
error: verification failed
Finished, time used: 18 sec
Remove/Install battery now !
After all this operations touchscreen calibration w/o fixing.