Abou touch screen

[.::skybird::.]

I flashed a SIGMATEL-S1. After flashing it's on Touch Calibration Wizard
but its Touch screen not working.

Is there any solution to (Shot any points) Operate it without change the glass or without Calibration???

Please share your some Experience about that

Thanks in Advance






br
.::skybird::.

[tkowsar]

I flashed a SIGMATEL-S1. After flashing it's on Touch Calibration Wizard
but its Touch screen not working.

Is there any solution to (Shot any points) Operate it without change the glass or without Calibration???

Please share your some Experience about that

Thanks in Advance


br
.::skybird::.


have 4 way.


1. some of device have "Skip Calibration" option, do it with this type of device.

2. can you replace touch.

3. collect same size touch from other phone, and after done Calibration, back it in collected phone.

4. flash you phone with a good and new file but don't format phone after flash. so you no need to do Calibration.

[.::skybird::.]

Thanks for reply but

1. some of device have "Skip Calibration" option, do it with this type of device.

I have Infinity and Xintel + VE dongle. In these no any Option (skip Calibration).

2. can you replace touch.

I am asking solution without replace touch because i think some people have any solution for that
May be by short some points and May be any other.


3. collect same size touch from other phone, and after done Calibration, back it in collected phone.

The costumer is on the point now therefore i can't collect any other.

4. flash you phone with a good and new file but don't format phone after flash. so you no need to do Calibration.

plz share if you have any file
eeprom[GINWAVE25_06B_PCB01_GPRS_MT6225_S00.FXD-S1-ML_MR106_004_5S02-MC-C01-RF3198_V1_1_025_080411.BIN]_20080916-045209.B0E

[PRINCE MOBILE]

i flashed a sigmatel-s1. After flashing it's on touch calibration wizard
but its touch screen not working.

Is there any solution to (shot any points) operate it without change the glass or without calibration???

Please share your some experience about that

thanks in advance






br
.::skybird::.




in infinity can touch celibration option availabel your mobile celi. With mathod 2 & 3 and your mobile start without cali. I try this before 2 day in s1 sigmatel. AND MY SET IS OK

[ssatcom]

I flashed a SIGMATEL-S1. After flashing it's on Touch Calibration Wizard
but its Touch screen not working.

Is there any solution to (Shot any points) Operate it without change the glass or without Calibration???

Please share your some Experience about that

Thanks in Advance






br
.::skybird::.

Try wirh Infinity.........

[.::skybird::.]

Yes I have been do it with Infinity by press "Calibrate Touchscreen" on Mode1, 2, and also on Mode3

here is log of Mode3:

COM1 [Serial0] selected
Action: touchscreen calibration
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:B803:0009
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: FXD-S1-ML_MR106_004_5S02-MC-C01-RF3198_V1.1.025_080411
Version: GINWAVE25_06B_HW
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #5 (mode-3)...
1 2 3 done
160 byte(s) read
writing data...
verification...
verification Ok
Finished, time used: 12 sec
Remove/Install battery now !


But problem not solved

[.::skybird::.]

I think this Option (Touchscreen Calibration) of Infinity is for repair the Touch screen
Not for skip the Calibration.

[skyangelfx]

Here you go http://forum.xda-developers.com/showthread.php?t=393425 , and may this can help you alot ... although it has worked for me on HTC but better you can try on your own product ....