ZTE-A139: we are looking for phone for tests

[InfinitySupport]

Dear Friends,

If you have ZTE-A139 model on hands and ready to spend some time in testing, please, contact us.

If you have this phone on hands and if you have Infinity-Box PinFinder please, make automatic pinout detection as MT6225 CPU and post pinout here.

Thank you in advance !

[cubafreak]

I have one on hands and time to spend on this, just tell me what to do. No PinFinder over here.
Regards.

[InfinitySupport]

Hello,

Phone connector has 8 pins only.
I am sure you can find GND and Charge pins easily.
If you can find RX and TX pins from rest 6 pins, please, read flash from this phone with ChineseMiracle software and send backup flash file to: InfinityBoxSupport@gmail.com

[djafter]

Hello,

Phone connector has 8 pins only.
I am sure you can find GND and Charge pins easily.
If you can find RX and TX pins from rest 6 pins, please, read flash from this phone with ChineseMiracle software and send backup flash file to: InfinityBoxSupport@gmail.com


sending backup of ZTE A139.....

and one message show by the box.

[djafter]

its the operations log..
unlock not work...
not supported yet..

COM9 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: "sp-unlock"
unlock method: standard fast
Unlock procedure can be faster if you skip eeprom area backup procedure.
Do you want to disable eeprom backup ?
eeprom backup disabled
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:6103:0003
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: ZTENJ25_07A_PMJ_PCB01_GPRS_MT6225_S00.SE-VE-MOVISTAR-P103C2V1_0_6B05.BIN
ver. sw2: SE-VE-MOVISTAR-P103C2V1.0.6B05, 00000000
ffs offset/size: 00A00000/00600000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00A00000
flash: 01227E22202200:2AEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00C00000
Detected eeprom/ffs address is non-standard: 00C00000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00C00000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 00400000
ffs chip: 00
eeprom/ffs area: 00000000:00C00000-00FFFFFF
detecting ffs structure pass 1...
..................
detect standard fat location pass #1...
................................................
detect extended fat location pass #1...
....................................
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
flash: 01227E22202200:2AEA0000000000
Backup required data Done
Patch required data...
....................................
lock area found
Patch required data Done
Special operation...
Special operation Done
Write...
flash: 01227E22202200:2AEA0000000000
flash: 01227E22202200:2AEA0000000000
Write: lock-area-1
Write Done
Finalization...
Finalization Done
Finished, time used: 127 sec
Remove/Install battery now !

[InfinitySupport]

Hello,

Thank you !
Please, try to keep phone with you for 1-2 days, we need some time to check flash backup.

[djafter]

ok...man..


I bought the phone just to test the unlock...

PD:: The Imei Change work perfect. ;D

we..are .waiting for your Answer ! XD

[InfinitySupport]

Hello,

Please, try to use this software: www.infinity-box.biz/download/public/MModule.rar

Try to use different unlock methods (read unlock codes etc.)
Waiting for your results.

[djafter]

not work...
the proces is done..

but NOT unlock the phone...

[InfinitySupport]

HEllo,

Please, try to unlock phone by all possible methods.
Send operation.log file to check: InfinityBoxSupport@gmail.com

What code phone ask to enter ?

[cubafreak]

I need the MModule to test with the one I have here. I can't download it.

[InfinitySupport]

Hello,

Here is it: Here is link to new software:
http://rapidshare.com/files/152123034/MModule.rar.html

Waiting for your results.

[cubafreak]

ZTE A139 unlocked OK, sorry for be late to report, personal problems.