CECT T3100 Flash File Required

[Munir Memon]

Sir;
plz give me a file of this modle chine CECT T3100. file name is:

( LC6223_07A_PCB01_GPRS_MT6223_S00.LKA8D01_07_36_1_3 T04M0118_M511B.BIN )


Thanks

Munir Memon

[InfinityHelp]

hello!

we dont have any other files than on support site.
isnt it is a second MCU firmware?
are you sure thath you need it? maybe it worth to focus on first MCU?

[Munir Memon]

Sir:
i am shure and i send you log opration file for your information so kindly send me this file.

Thanks

Opration file:

==== log: [10/5/2008 7:33:04 PM] ====
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: "format ffs"
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6223:8A04]...
CPU: MT6223
high speed boot enabled
chip: 0011:3400:000C
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22212201:2AEA0000000000
flash: Amd AMD/Fujitsu std [def 0080x020000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212201:2AEA0000000000
flash: Amd AMD/Fujitsu std [def 0080x020000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22212201:2AEA0000000000
flash: Amd AMD/Fujitsu std [def 0080x020000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22212201:2AEA0000000000
flash: Amd AMD/Fujitsu std [def 0080x020000] 16Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: LC6223_07A_PCB01_GPRS_MT6223_S00.LKA8D01_07_36_1_3 T04M0118_M511B.BIN
ver. sw2: LKA8D01.07.36.1.3T04M0118_M511B, 00000000
ffs offset/size: 00C40000/003C0000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00C40000
flash: 01227E22212201:2AEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00D20000
Detected eeprom/ffs address is non-standard: 00D20000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address[00D20000] confirmed by user
detecting eeprom/ffs size...
eeprom/ffs size: 002E0000
ffs chip: 00
eeprom/ffs area: 00000000:00D20000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Fail
Finished, time used: 53 sec
Remove/Install battery now !

follow this and reply me your many thanks

Munir Memon

[InfinityHelp]

hello!

6223 MCU is ussually second MCU.
can you open phone and check how many and what types are your MCUs?

what did you use to find pinout?